YaheetechAdjustable Squat Rack, Multifunctional Heavy Duty Barbell Stand, Strength Training Dip Station, Fitness Power Rack Weight Bench Support for Home Gym, Max Load 250kg, Height 114-179cm

The media could not be loaded. This review is for the (Yaheetech Adjustable Heavy Duty Squat Rack Stand Power Weight Bench Support for Curl Barbell Olympic Barbell Free-Press Bench Black)To enable me to squat and chest press during this Covid-19 pandemic, I required a rack, although having limited space I needed a compact option, therefore I went for these squat stands due to its ability to also act as a bench rack as well as a squat stand.Building itFirst off, in order to build this, I cannot stress enough that you require a spanner and a quick release ratchet in order to tighten the 48” bolts. If you don’t, you’re going to have a difficult time building it and it may become a two man job as the main beam wobbles while you try and tighten the bolts. Therefore, while I was able to build these myself, I recommend having a second person to stabilise it to make construction easier.Other than that, building it is very straight forward and it came with all the required components and screws. My only issue is the rubber feet as one came damaged and I had to reshape it using a pair of pliers so that it would fit the legs of the stands.Design/QualityThe stands are made from heavy duty metal and each stand weighs about 10kg and are relatively light to carry.Wether this adds to its stability or lack of, the light weightiness of these stands make them an easily portable solution. The stands are rather large as represented in my review photo, contrary to the original photos.The stands legs are a ‘H’ shape and come with rubber feet which stop the stand from sliding when loading and unloading the rack. The H shape of the stand acts as a counter balance to the weight during heavy loads so that the stands don’t tip over.The stands also come with heavy duty J-cups which act as spotters during a chest press if one cannot re-rack the weight during a lift, or for resting the bar after bicep curling. They are easily adjustable and do not get in the way during bench press, allowing for full range of motion and can be removed.The rack itself catches the the bar easily, although my only issue was the welding. While its considered minuscule, one was not completely welded leaving a space which offset the alignment of the bar a little.One must bare in mind that while these stands are sturdy, they are also independent of each other and bolted, therefore they do wobble under heavy loads and weak screws can damage the integrity of the stand and its ability to hold weight, so my advice is to be cautious with how much weight you use.Overall, the stands are lightweight, yet sturdy and a do a great job of allowing both squats and chest press.AdjustabilityBoth stands are adjustable and stand at a height of 3 ft 8 inches (114cm) and can be adjusted to a maximum height of 5 ft 10 (179cm).With any telescopic feature, as these stands are adjusted higher, they lose even more stability due to the lack of even weight distribution at its base. Therefore, if you are a very tall person looking to rack a lot of weight, these may not be for you, unless you are able to counterbalance the weight.Adjusting the bench to size becomes easier the more you do it. Each stand comes with a safety pin to hold the the adjusted height and a screw to hold the jcups.In order to adjust them, one must remove the screw holding the j cups and then the safety pin. This becomes rather time consuming for switching in-between bench press and squats. However, the more its done, the less of an issue it becomes. If time in-between sets is an issue, I recommend getting a stand with a pull out pin rather than a screw as it would save you a lot of time.Weight CapacityThe stated maximum weight capacity which these stands hold are tested at 220kg.One must bare in mind that static load is very different from mobile load, therefore don’t expect to be squatting 220kg on these as it wobbles way too much when racking the bar under heavy loads.As a 78KG man, I was able to bench press 100kg and squat 140KG, although the stands wobbled a lot when the bar was racked.This may pose a safety issue for someone if they are not careful when racking the bar. As a way to add stability, while its unconventional for some, I read that others fill the base with sand to add weight. You can also use weight plates at each end of the legs, but this becomes time consuming and ruins your plates.I found that the best solution for counter balancing the weight was to weigh 20kg+ sandbags at each side of the legs as they cover the full diameter of the legs.The only other con of these stands is that if you do not have a rack for your plates, loading them on the bar is difficult from the ground.ConclusionOverall, these stands are a good solution for individuals that lack space and are not looking to lift a heavy weight load.While these stands can bare a lot of weight, remember they are bolted and can lose integrity from damaged screws, they are also independent from each other, posing a safety risk of one falling during a lift. Therefore, I recommend these on the basis that one is a beginner or is very careful when using these for lifting.As time goes on and weight increases, one might look into replace these for a full or half rack.I hope you found this review helpful, happy lifting.

Easily assembled, sturdy and good value for money

Arrived 2days early.Very well made and sturdy, built for purpose. Well ok impressed

The quality of the product is great, item is sturdy, easy to assemble if you have 2 17 spanners hanging around (would be difficult if you don't have your own tools), I found the screws supplies based on the instructions go further than the base of the unit so the "Rubber feet to protect your floor" won't do anything if 4 screws stick beyond them, I undid the screws and did them the other way around to avoid that issue. You can see how far out they stick on the bottom left of the imageAfter using a few days:Pros:- Easy enough to carry around (~9kg per side total ~18kg)- Good instructions to put together (minus the screws mentioned above)- Feels well built, I feel I can trust it with the weights on- Pins and screws for height adjustment fit well- Central stands and top stand are perfect heights for a 5ft8 guy with an average gym bench in between- I believe it is value for money, happy with my purchaseCons:- 4 Screws on the bottom according to the instructions would damage the floor unless done the other way around (which you could end up stepping on the sharp ends instead)- No tools supplied to build it, I used 2x17 spanners for this, it was easy to assemble if you have the tools- Some of the parts supplied have some nicks in them, such as the supporting plate on one stand has some grooves in it as if something was dropped on it in production, some washers had chipped off edges and one of the nuts was missing the plastic insert inside it to help it be stuck tight once on- Not very well packaged, thin plastic wrappings on each piece but they all slide around in the box so some minor scratches but not anything I care about

Very sturdy as would expect from this brand. Perfect for home workouts. I would have liked the hooks at the top to be a bit longer as you have to be careful when placing the barbell back, you have to be quite precise.Would I recommend, absolutely.

good quality, very useful and multifunctional

Bottom of the pile squat stands that do the job. If you’re looking for some squat stands that won’t break the bank these will probably do. Very basic but functional stands. Like others have said there was some rust within the tubes and some of the holes didn’t align when putting together…one of the stands is a little wobbly due to one of the cross bars being slightly bent at one end….the spotter bars are very short and I’ve found mine won’t adjust if there’s a loaded bar on the stands, so set these up to the desired height before putting your bar and weights on. Also found these work best with a 6 foot or bigger bar

Will use these for squats and are very sturdy. Easy to assemble and use. Great value.