ASUS Pro WS WRX80E-SAGE SE WIFI AMD Threadripper Pro EATX workstation motherboard (PCIe 4.0, ASMB9-iKVM, 2x10Gb LAN, 7xPCIe 4.0 X16 slots, 3xM.2,2xU.2 ports, 11 USB 3.2 Gen 2 ports,8-channel DDR4 ECC)

Desafortunadamente el producto enviado por amazon no funcionaba.

Mounting booby-trap: Circular silkscreen, around all mounting holes, clearly indicates board-mounting screw's maximum head-diameter. But conical shaped bore, in uppermost left corner of board (near i/o shield top), is smaller than that maximum diameter. A screw that fits just inside circular silkscreen, elsewhere on board, is too large for uppermost-left mounting-screw position. A screw placed in that bore will get stuck, with certainty, inside the conical bore with no way to extricate it except by removing the entire board, disconnecting all cables, then drilling out the screw in peril of mechanical and electronic damage. This booby trap occurs because the conical bore jams the screw's head before its threads fully seat the chassis bolt. Turning the screw, in either direction, strips its head. ____________________________________________ Why is there an absolute upper limit of 30 minutes on ASMB9-iKVM IPMI BMC web service interface? Why can it not be changed to a longer duration? We need to monitor over 24 hours without automatic logout. Where did the arbitrary 30-minute-limit gaffe originate? Here's another gaffe: If the motherboard is powered-up continuously, then any attempt to log in to the iKVM by browser will indicate "session expired". This happens after some indeterminate amount of time is passed. A manual power cycle won't fix this. The only way to get around it is by cutting power to the board from the mains supply switch. ____________________________________________ Every engineering school in the US teaches that blinking light denotes error condition. Every industrial OEM manufacturer, in the US, blink LEDs only on error condition or data transmission. (The only groups of people who prefer blinking lights are police officers and gamers.) Why does the BMC_LED blink green in absence of error? Why does the MESSAGE_LED not blink when reporting an error? The motherboard is powered down and the BMC_LED still blinks. Why? ____________________________________________ ASUS ASMB9-iKVM interface, for IPMI BMC, interprets 0 RPM as "Disconnected". But 0 RPM is a valid state of a connected fan. Setting 0 thresholds could be a way to work around 0 RPM being falsely reported as failure. Why can't upper and lower RPM thresholds be set on disconnected or 0 RPM fans? ____________________________________________ There is a two-digit 7-segment LED display providing board status in hexadecimal code. These LEDs represent a throwback to 1983 when Z80 microprocessor demo-boards needed a display. Asus is very capable of providing an elegant postage-stamp size color LCD display right on the motherboard, as it does for gamers. As it is presently, we are forced memorize 256 hexadecimal codes or take an inordinate amount of time to look them up, presuming the motherboard's user manual is handy. Asus: please put an LCD display on this board to communicate board status. _________________________________________ Chipset fan is problematic. Nbartowski reported the exact same issue on level1techs.com in May 2021. BIOS would report a critical error: that Chipset fan was spinning down below critical level. Examining it through the IPMI BMC interface reveals its status as N/A. Error manifested as blinking LED notification on motherboard. This blinking error indicator would occur reliably when the power supply (PSU) line switch was turned on for a few minutes without subsequently turning on the computer (motherboard) itself. Error indication stopped when powering the motherboard immediately followed supply of line voltage to the PSU. When that was done, the motherboard Q-code 7-segment LEDs began a countdown from hexadecimal FF. Error indication hasn't been seen since, Chipset fan only spins during POST, but BIOS still reports N/A Chipset fan (but no blinking LED). ASUS customer support recommended returning the motherboard on an RMA, but this turned out to be a BMC firmware issue. BMC firmware installation has about 5 unnecessary steps. In the 17th step you are asked which of the 13 firmware modules, in particular, you want to flash. The problem here is that version numbers, associated with each submodule and currently installed module, are incorrect. So by selecting only a subset of modules to install, the Chipset Fan problem is introduced. The solution is to flash the entire BMC firmware suite and to overwrite what is already there. Provide line voltage to the Power Supply Unit, then don't wait to power up the motherboard. The 7-segment Q-code LEDs will then go into countdown and later the BMC_LED will blink green. Then the IPMI BMC interface will report Chipset Fan at 0 RPM, which is probably normal under small load. ________________________________________________________________________ I have little confidence in ASUS customer support because they couldn't answer simple questions about the board's operation, and I don't think they have actual access to ASUS products. Every time a question became a little beyond what they could find in the User manual, the problem got escalated. But I was never contacted by engineering, so it is impossible to get answers from someone at ASUS who actually knows what's going on. I can read manuals; I don't need ASUS' Placating Response Team to read the manual to me. ________________________________________________________________________ In the User Manual for this motherboard, only Windows 10 is listed as compatible Operating System. Yet we know, a priori, that any motherboard must be OS independent. Immediately after a fresh Windows install, there appears an Asus Armoury Crate icon in the System Tray (the right side of Taskbar). In the BIOS, there is a selection to disable Armoury Crate. This means that the BIOS has altered a clean installation of the Windows 10 Operating System; specifically, the Windows System32 folder holds executables named AsusDownLoadLicense and AsusUpdateCheck. This is the first instance we've ever seen of a BIOS injecting high-level executables into the OS. This practice is unprecedented. If not stopped now, then there will be no limit to the amount of adware, sludgeware, updateware, notifyware, and telemetric spyware stealthily injected into the OS by a Windows savvy BIOS. ASUS: The practice of OS alteration by any BIOS is unacceptable. Discontinue this practice. By that I mean, completely remove the option to inject Armoury Crate into the OS. Do not merely disable the default option; remove it altogether along with any stealth firmware that can inject executables into the OS.

This is the second Asus Pro WS WRX80E board I used for a video editing build. Yes, it costs real money. Yes, it's big. Yes, it's have. That's what I wanted, especially all the PCIE slots, onboard M.2, and massive memory support. I loaded this particular unit with a 3090 video card, 256 of RAM, and a 16 core Threadripper Pro. It hums along, editing 4k video with zero issues. Also, the enclosed Hyper m.2 card gives room for 4 more ssd's. These provide fast storage options depending upon how you want to format it. I also used some PCI cards to hold old 2.5" ssd's that become scratch drives for sample edits. One advisory: Be sure to update the BIOS and understand how all that works for your particular needs. Take your time and plan out the build for best results.

Pros: -Great Quality -Tons of PCI-E ports Cons: -Both Asus and Amazon DON'T say that this is an "EE-ATX" motherboard (Extra Extended ATX). Bought three different cases because all said "E-ATX" compatible. The ONLY case that with compatible mount fittings in the correct positions is the "Corsair 7000D Airflow"! -The bios DOESN'T allow you to change fan speeds nor pump speeds for AIO loops. You have log into their IPMI through an internet browser. The ipmi switch must also be physically turned "on" on the motherboard. Super tedious and pointless. Just make it available in the bios, Asus!!! -Backplate on motherboard makes it difficult to mount the motherboard. You have to bend the backplate inward in order to make contact with the mounting holes of the case. -Take off 1 star because of the IPMI and wonky backplate.

dont buy this item if you put 7 gpu into the 7 pcie slots it gives aer error of fails to boot. and one ram slot did not work. upon reading online many other users had this issue. infact this item i received had already been registered for repair with asus in korea and they made me send back to korea to repair and then charged me 500$ out of my refund even though they accepted my refund and the manufacturer offers 36 month warranty or replacement. the asrock motherboard does not look as nice but doe not have these issues. you can adjust the retimer settings to get to boot but will full your terminal with aer errors.