[Updated] New Model Pistol Sight Pusher Tool with Heavy-Duty Construction for Handguns Front Rear Sight Removal Adjustment

I bought this with a little optimism hoping it would work on my Springfield XD since they have notoriously tight sights. This sight pusher after slowly turning the pusher broke them loose and eventually right on out. With ease might I add. Granted I used some regular gun oil to soak the sight first. The 5 way adjustment is perfect for centering the slide and holding it in place firmly. If you are considering this for difficult sights do it, you will be happy .

Easy to use. Nice and heavy. Feels durable. Worked perfectly. Beretta sights are known to be difficult. This did the job.

This tool is excellent and I recommend it.I used it to install front and rear sights on an M&P 2.0, which had previously given me so much trouble to remove that I had to go to a gunsmith. It's well made, feels and looks solid and it is fairly straightforward to use. Make sure you read the instructions and double check your alignment before committing, because there is the potential to do some damage, this is tool is strong.Aside from the additional blocking pads that you can use depending on the shape of the gun slide, and the handy ruler at the top which helps with centering, the biggest advantage is that it fits a standard 2½" vice (actually only needs about 2" clearance), which means it will hold everything nice and steady and free your hands and attention for a better job at the gun sights. Operation is safe and easy once you set everything up properly, but it's not difficult, and amazingly it just works! You may want to lubricate the inlet for the sights before insertion, the tool does make some worrying noises under strain, I moved back the pusher and then forth again to avoid exerting too much pressure for too long, and it worked.It does however have a little design flaw in my opinion: the bottom block, used to place it in a vice, has the top corners rounded as shown in the picture: this means that you can't get a proper flat grip against the vice unless you raise it a bit, which makes it less steady. It may give more solidity to the frame, but I think it should be a proper 90° angle in there.Secondly, and that is the biggest flaw, the thread on one of the vertical bolts was damaged in two places, as shown in the picture, so much so that I couldn't screw the nut further down. I had to scrub the groove several times with a flat screwdriver to make it better, and then insist with the nut back and forth with oil until it finally let it through - just as well or I would have not been able to use it. Being the most important part of the tool, I think Sporgain should make sure all threads are sound from top to bottom before letting out the tool from the factory.Apart from these two (minor) flaws, the tool is a phenomenal piece of equipment at a very good price, especially if you plan on changing sights more than just once: saves you time and sorrow!

Very well made and easy to use. Comes with filler pieces to accommodate different shaped slides

It is very well designed and very easy to use. It can precisely adjust the sights of the pistol and improve the accuracy of shooting. I especially like its stability. The push rod operates smoothly and does not cause damage to the pistol. The material is sturdy and durable, and the quality is guaranteed. I have to say that it is very cost-effective and highly recommended!

Was looking for a more heavy duty site pusher after the cheap plastic one I bought off an online bidding site cracked on me. This one was perfect and did the job without any hesitation. I also like how you can use the holders to get it perfectly lined up

I pushed out the front sight on a s&w m&p that was extremely tight. I used this press in a manner that was bad. i had to tap the vise crank handle with a rubber hammer to put more pressure on the sight and used a brass drift punch tapping on the sight to get it to move and this vise stood up to extreme abuse. no marks on the slide or sight. Highly recomended for the price.

Very simple and easy to use sight pusher. The material feels strong and not cheap. My only complaint is the plastic fitting you add into the sides to hold the rail are not meant to last. But just keep in mind this product doesn’t work as well with slides that have a safety switch on the back such as Beretta.