Co2 Tank Cylinder Direct Adapter (Gauge and Bleed Valve), CGA320 to TR21-4 Soda Machine Adapter with 60in High-Pressure Hose, Compatible for sodestream Soda Maker, Adapte to fizze/one touch/jet

The media could not be loaded. Update:Purchased this to use in conjunction with a Vevor 5 LB CO2 tank.It worked perfectly to hook up to my iGulu brewing machine.The pressure meters matches between the one on this adapter and the one on my machine.As far as I can tell so far there are no leaks, and it was as simple as screwing it in.It came in a box with directions as well as extra parts.After using it for a while I found that it was actually leaking a small amount resulting in the 5Lb tank draining far quicker than it should have. Looking close I found that one of the yellow brackets was cracked and the hose under it looked like it had been crushed. I contacted the seller and let them know and they sent me out a replacement right away.The replacement looks perfect and appears to be working well so far. The steps that come with the directions are not correct and indicate washers need to be inserted when they already come that way.Highly recommend both the product and the seller for their quick and prompt support.

I have to admit I was pretty skeptical. I have one of the first and simplest Sodastream makers (canister holders) and figured there might be some serious issues retrofitting an old but full CO2 canister my brother in law cast off from his old keg fridge. Didn't I need a regulator? Was this going to blow the seals? was that hose going to be strong enough? After using this for several months I can say that this is everything you need. No regulator needed - the gauge shows a constant near 1000 psi. I cut a notch in the bottom of my Sodastream to accommodate the hose through the base and it works great. In the first month I had a couple issues with some kind of back-pressure, but there is a bleeder valve near the pressure gauge, so it's easy enough to cure. Really no issues since then. Maybe eventually this setup will kill the seals, but so far, in savings it's paid for itself, and a replacement Sodastream base if it comes to that.Update: was having an issue again with not getting CO2 through the nozzle, so I went through the process of tearing everything down to see if there were issues with the seals. After looking at how the entire system is designed, I wound up resolving the issue by running a small needle through the end of the nozzle that injects into the water bottle to dislodge some piece of debris that found its way into the system. This is something that could happen even with the regular bottle exchange - and is perhaps even more likely with more frequent changes. After examining the connections and essentially very simple design of the system, I can say with a fair amount of confidence that you would be extremely unlikely to have "seals" fail (and that cleaning a blocked nozzle is something that can be done without tearing down the entire system). If the bottle is over-full, you can get some leakage through the pressure seal especially on the first injection, but after air drying between uses, it's an occasional minor annoyance that is easily prevented by either not exceeding the fill line or using a more gentle press on the first injection.

Works great with my Fizzi. Easy to connect.

I have another similar hose that feeds my Soda Stream that is connected to a 5lb Co2 cylinder. This hose works fine but is braided and very stiff. I thought I would try this hose as it is more flexible.It worked great for about 8 days. I noticed the my tank of Co2 only lasted about 8 days or so and needed to be replaced. Normally, I can go about 6 weeks. I thought the tank might have been light or some other problem but the place that I swap them out said the 5lb tanks are the only ones they weigh to verify they are full so getting a light one wasn't likely.I connected the new tank and this new hose and adapter. After about 8 days I noticed there was no pressure going into the water bottle. I checked the new tank and there was plenty of pressure left.I disassembled the connection and plugged in a regular Soda Stream canister and all worked fine. Then I plugged to new hose back in and the valve that connected to the Soda Stream leaked audibly. I tried to tighten it but risked breaking the soda stream so I replaced this hose and adapter with the old braided on and everything worked just fine.I am guessing there was a slow leak that accounted for why the first tank ran out so fast. The the valve failed altogether and the leak became audible.Liked the flexibility but perhaps their QC could be better. Can't recommend this system at this point.

Worked well for about 9 months before the seal on the hose went out where it is crimped on, I manually opened the valve on the co2 tank for each use otherwise it will slowly leak, so 4 out of 5 stars.

Just what I needed. I was tired of switching out little containers of CO2 in my sparkling beverage maker. Now I can purchase a 20 pound tank of CO2 and use this excellent hose to connect the tank directly to my soda maker. As always arrived as described and on time.

I desperately wanted to like this product. The build quality seemed sturdy and decent. After putting it all together I had constant air leaks. First was with theAir release Pin that interacts with the soda maker. Once I was able to fix that issue by jiggling the pin around, I found there was also a leak between the quick-connect connection and the adapter screwed into the soda maker. It took me a while to figure it out but the wrong sized O-rings were pushed down into the quick connect opening. They were much too big for the opening, causing it to not seat properly with the adapter. I pulled that out and used the spare O-ring provided and that one is too small, still not allowing for a proper seal. After trying all I could with the items provided, I am returning it and looking at a product from a different manufacturer