IWISS SN-2549 Crimping Tools for Dupont terminal 0.08-1.0 mm² XH2.54/ 2.54/2.8/3.0/3.96/4.8/KF2510/JST Terminal Crimper Plier Ratcheting Wire Connector Crimping Tool

Very impressed with the ease and accuracy of these crimping pliers. I have other pliers which are also designed for uninsulated crimps and which have a flat head on one side of the jaws which, if you're not very careful, can rotate the crimp so it doesn't compress properly. But these pliers have a cupped face on rhe second side which is perfect for closing down the crimp. Particularly useful on the small 2.54 pitch molex kk type crimps. Great results.

I needed a reliable crimper for small non-insulated connections and this IWISS tool is great and delivered by Amazon the next day through the letterbox.Previously I'd bought a cheaper generic SN-28B tool but even when using the correct connections the crimps I was making were failing and not formed correctly so I was wasting a lot of connectors. Buy cheap buy twice I guess.I've had IWISS tools in the past and initially missed this one when buying the SN-28B but gave it a go as the previous tool wasn't very good.Immediately the same set of non-insulated connectors I've been using are formed better on both the bit holding the cable insulation and the smaller part crimping the wire and most importantly aren't failing in the pull test or giving me random continuity problems.There's a bit too much wire in the cable in the pictures and I've also shown the size next to a pen - these are little so just a mm too long makes quite a difference!You also get some good instructions with these whereas a lot of crimpers you'll be left to your own devices to work it out (although they all have their own pitfalls, it just takes time to get used to each set).For me definitely worth paying that little extra over the generic crimpers if you value your time - these aren't as expensive as proper Molex crimps but still seem to do a more than good enough job.Thanks IWISS!

Because I didn't read the descriptions I ended up receiving the wrong one. As it turned out the one I received worked well for Molex lose crimps so I kept it and re-orded the JST version. The moral of the story is read carefully what you are buying.I am not sure I am using the JST tool correctly but you need a knack that comes with doing ten or so crimps. You can crimp directly from the strip of crimps and use the edge of the backing material as the alignment face. I have had more success by breaking out the crimps and using them loose. I use a small darning needle in a handle/holder which I partially insert into the socket end of the loose crimp. This grips the crimp and allows it to be rotated and so you can push it into the face of the tool so the small retaining tab acts as a stop. Once located the jaws can be partially closed and the wire inserted. I'm sure others will have different ways of doing it.For the price and for the number of crimps I am likely to do in my remaining life time it is a good price and more than good enough quality.

ProsDecent crimping actionEasy to operateDecent gripsConsA little priceyLimited crimping optionsI needed some JST 2.0 Crimpers, and there came onto my radar. I picked them up, and after a bit of messing around I got them crimping my connectionsOverall they did a decent job and held the connector well. The finish was excellent, and the wires were all secure.These are a little pricey as they don't offer many options for different crimping bits. They do not have interchangeable teeth which is a shame, but what teeth they do have are decent.

Was planning to purchase the Paladin die for JST-XH for my paladin crimper, but it was on back order and this was cheaper than just the Paladin die....and i really needed to get on with finishing some crimps.Was really surprised with the quality. Solid feeling, smooth operation and ratcheting that helps to hold the pin firm whilst you insert the wire and then crimps perfectly without crushing.Not much more to say really...does the job, makes the job easy and is built to last.Definitely recommend!

I had almost given up with finding an affordable, easy to use crimping tool, for Dupont plug and socket crimp connectors that provided a crimp as good as the mass produced breadboard jumper wires.If you can get good mass produced jumper wires why bother with a crimping tool, It all about length with longer wires you get problems with the way an electrical circuit will operate. So I like to use commercial jumper wires and tailor them to the length I need for each part of the breadboard circuit.The"WISS SN-2549 Crimping Tools for Dupont terminal 0.08-1.0 mm² XH2.54/ 2.54/2.8/3.0/3.96/4.8/KF2510/JST Terminal Crimper Plier Ratcheting Wire Connector Crimping Tool "has proved to be the best quality crimping tool to date that I have found. A*********The ratchet allows the tool to hold the crimp pin or socket securely while inserting the wire.Once the tool is fully closed and springs open the crimp pin is easily released unlike other brands and the wire and sheath crimps are showing the same closure as the machine produced crimps, with a similar insulation resistance end to end as machine made crips.The crimp tool is a good fit for my hands and the crimping pressure required to complete the crimp is comfortable for making 20 or 30 crimps at a time.Really glad I bought this tool, Amazons delivery time was also fast.

I bought this as an alternative to MDPC-X tool for crimping my ATX PSU cables. Obviously this is 33% of the price of CTX 3. Nevertheless, this isn't really suited for crimping terminal pins for ATX PSU. The teeth of the insulation wings are not curved enough and as a consequence you end up with flatter pin, which hardly fits in the connector.In order to make it fit, I need to use the middle teeth but because if the thicker wire I end up with one insulation wing broken. It will work for now but for my next job I will need to get different set of crimps.Maybe I will even return these ...