Full Face Respirator Mask with Filters: 6800 Gas Mask with 6001 & 2097 Filter Reusable Organic Vapor Mask Against Fumes Gases Dust for Painting Epoxy Resin Welding Construction Emergency Polishing

This mask works great for my different projects. Very easy and simple changing the attachments. I did have to look up how to properly use it in a video because the directions were a little confusing for me. Once I figured it out it was great! I use it all the time for my spray painting, when I'm using my resin, when I'm sanding. I would highly recommend. The first thing I used it for was my spray paint in and I'm not sure if it's just the scent of the spray paint that is stuck on the mask but every time I take the mask off I smell that same smell every time

I recently purchased this to use while cutting and polishing rocks for lapidary use.I'm really happy with it. I purchased another mask that was too small for me that unfortunately, I couldn't return. The nice thing about this mask is that you don't need to have safety glasses, you get the whole thing all in one.The seal is excellent (and I have a short beard - no problem at all. When I do the seal test on it - tight seal.And it's comfortable. I had it on my first time for over 2 hours and was pretty comfortable working in it the whole time.

I have been using it for about two months, i use it almost everyday at work. I did buy some window tint and put that on the inside to help block the sun and that helped a lot. over all this is better then the 3m one that i had that did not have the face cover but had flimsy straps.

It's not bad. I get a good seal and the mask is good but I did have one of the tabs break off the first time I tried to attach a filter. Be careful of that and it should be good

I have been using this mask several times a week for 3 or 4 hours a day while working with both woodworking equipment (saws, sanders, blowers etc) and epoxy resin. I really wanted it for resin work because I get itchy when touching and breathing resin fumes. Using this mask, I seem to have eliminated my exposure to the fumes. I do wear Tyvek coveralls and gloves too so I am pretty well protected. I am 6'0" with a fairly large head and this mask has been very comfortable. This respirator mask barely fits me, however, I still have to pull the straps a bit to get a nice tight seal. If I do not, I can smell a little bit of the fumes seeping in. I have been doing DIY work with paints and chemicals for more than 30 years and have always found other respirators to be uncomfortable, but this is my first with an integrated face shield and respirator and have found it to be comfortable where I hardly notice it, even after wearing it for several hours. The visibility through the face shield has been very good and has not fogged up on me. Hope this helps...

So I put value for money as outstanding, because IF it was good, 27 bucks would be ridiculous, but IT ISN'T. Seriously, I would caution against it. When I first put on the mask, I did a seal test, with nitrile over the filter ports, and it didn't seal right away. Shuffled it around several times, seemed like it got better, so put the cartridges in, I had to complete a job with Isocyanate Primer. Started spraying. Immediately I could smell the solvent. Rushed out, fortunately I still had my 3M half mask and good 60921 cartridges. I could see that this full-face is a 1 to 1 copy of the 3M that costs about 200, so I was pretty giddy to get it. Huge mistake. In addition, the lens is optically distorted [kind of important with paint work], and one of the P100 caps was broken. I've always resisted getting a full-face, even though with Iso's it's highly recommended-eyes are a mucus membrane-, because of the layer of vision obstruction, this-for me anyway-was just next level failure. If you're doing this work constantly, it's worth investing in the 3M high-end silicone one, I've used it and the vision obstruction was tolerable, seal is complete, but just not 450.00 good enough for my limited time in the booth. YMMV, of course. Amazon Assistant is awesome. I wasn't saddled with the loss, but trying it wasn't worth the time.

I recently used this mask to clean a chicken coop and I couldn’t smell a thing! I love that it covered my eyes too. I will be getting a lot of use out of this on our mini farm. It was very comfortable to wear for my 2 hour task.

Just like the 3m brand.