USC Spraymax Matte Clearcoat 3680065

I do alot of hydrographic dipping, I need a finish I can trust to last. From Matte to High Gloss this stuff works, not only is it tough, but it looks great. I tell all my customers that sure there is more expensive stuff out there, but do they really want me to use it a find out the hard way that it doesn't work as well?⚠️WARNING ⚠️ make sure whatever you are using it on has been prepared properly and is been decreased or you take the risk of getting fish eyes (bubbles caused by Silicons or oils.). FISH EYES ARE NOT THE FAULT OF THE CLEAR BUT ARE THE RESULTS OF POOR PREPARATION.MAKE SURE YOU USE THIS STUFF IN A WELL VENTED AREA AND ALWAYS WEAR A PAINT RESPIRATOR!!!!!!.if you follow all of the manufacturers recommendations and or watch some videos online you will get a tough long lasting and beautiful finish that you desire.

Perfect matte finish, easy application, professional results every time!

I restored my recently purchased ‘96 Honda Shadow VT1100C2 with SEM Trim Black paint (spray gun style at 25psi), which has a satin finish. It was perfect. I was nervous about using an aerosol matte over the top of such perfect and durable paint, but my senses told me it would be good for longer lasting durability. I took the risk. No one on the interwebs mentioned using this product on SEM Trim Black. I’mHere to tell you that I’m happy I did. With the paint, I applied three coats, 5 minutes apart at 25psi. I warmed up the Spray Max right before I was ready to start spraying the color by soaking it in a bowl of warm water. When it was time to get the van ready for application, I dried the can off very well, shook it for a minute, activated the hardener, shook it for a whole minute, checked the wind with my wet finger, and sprayed. 2 light coats 10 minutes apart and a final light-medium coat. Do not go heavy. Follow 10 minute rule. Follow top coat rules and when your respective manufacturer says it’s safe to spray (don’t spray too soon or a couple hours after top coat or you’ll have problems). Make sure you don’t get overspray on other parts you painted as it will dry to dust and land on the other parts. After 5 days, I wet sanded with 5000 grit sanding pad. Wet sanded. 5000 grit. Do NOT use 1500 or 2000 on matte finish, you’ll destroy it (I sampled the back side of a side fairing and learned this). I wet sanded any areas that had a dusty texture and got it smooth and satin-yyy. Do not leave stripes. Slow, but not too slow sweeps to the left, up a couple inches, to the right, up, etc. so many people do not know how to use aerosols and get on Amazon and complain. Same people can’t adjust a toaster, either. Watch some YouTube videos and do this right and you’ll say man, $20+ a can was worth it!! A pro would charge hundreds for the same finish. I can’t verify the 48 hour shelf life. I also used this over VHT flat black wheel paint on the front forks, rear struts and seat pan with the same awesome results. Did not use on the pipes (they exceed heat rating, go with VHT flame proof paint and clear if you wanna do your pipes). My pictures are pre-wet sand. It only got better after the wet sand and some Flogenix protectant spray.

After failing by using clear coat from a big box store, I went the real route and got 2k clear to re-coat a carbon fiber spoiler and interior trim pieces...after appropriately sanding and cleaning up from my prior mess.This went on SUPER smooth and clean. dried to a perfect matte finish and saved me a TON of money by allowing me to DIY.Highly recommend.BUT...make sure you've got all your pieces ready to go once you start spraying. Lasts a few days in the can then hardens up.

It was a good product very hard to spray it was so flat you couldn't see where you covered

I’ve used the 2k clear before and loved it.. straight up show car finish. Only downside is the pot life:( but if you’re planning on using the whole can.. it’s hard to beat. This stuff lays on much lighter than the clear but the results are legit! But hard to find info on the cut and buff process!? I’ve herd of spray can matte finish that you can wet sand and buff and it still stays matte I have yet to see if this is the same but I’m super stoked on the outcome. F.Y.I anybody on here that gives this stuff a bad rating they did something wrong at some point of maybe got a defective can. And also anyone looking for a 2k clear with a long pot life a company called car-rep has a clear coat that doesn’t go bad right away!

I use this after doing a Surfboard repair. There was a crack in the deck and I had to airbrush with acrylic paints over an epoxy board. I use this as my topcoat to protect my acrylic paint and it looks good. Nice Matt finish. The only issue I had was the instructions on the can were pictures and I thought I had to aggressively push down on the bottom to activate the two-part spray when I did this it bent a little bit to one side and got all over my hands and the concrete. So, I'm not really sure I got the proper mix and was a little disappointed in the can instructions. I'm not sure but I think I was supposed to carefully press down on the bottom to activate the second part. There's no reason to be aggressive. I bet just guessing because the can instructions are pretty terrible. Hopefully, this will be a good protection, even though I'm not sure I got both parts mixed well because so much went on the ground.

you get about 48 hrs of use, once you pop it..Works great, lays on smooth when used properly.