Horizontal Mini Bar Clamps

Solid, well built, easy to use. be careful with the allen screws and make sure not to round out the hex head.

I used this to make a side table to attach on the bar of my day bed. It worked perfectly! I like that the hole sizes are adjustable and come with different sized rubber rings to properly fit the bar its attaching on. I had to keep sizing up on the rubber ring to get it to fit! It was a tight squeeze and needed a lot of effort to get the screws to screws but it works and fits! If you put some weight onto the side table it does slip down, so just something to be aware of. But it was exactly what I was looking for and holds my drinks and food perfectly.

Why did you pick this product vs others?: Good quality part that will withstand elements Build quality: Very robust. Well machined tolerances Look: Great aesthetics for use in visible locations.

For $9 on a 2 pack these brackets fit my needs of adding auxiliary lights to the crash/engine bars of my motorcycle. There was only 2 issues with these, first was fixed with a bit of hardware store parts and know-how. The second was one of the set screws stripped the threading right out of the bolt. The 1st issue is the inner diameter of the mounting hole where you would fit a CB antenna, bolt from the light bracket, etc is 10.45 mm in diameter (used a micrometer on both to verify). This is HUGE when the application I was using this for was a M6 bolt (6 mm diameter metric bolt). Remedy for this was a rubber bushing as I couldn't enlarge the bolt size from the lights I'm using. $4 for new hardware to marry the 2 light to the 2 brackets. No biggie. The 2nd issue is partially my fault, but also the cheap bolt provided. The metal is SOFT. Since the mounting application was a crash bar there was an inner and outer bolt in relation to the mounting position. Tightening one 2 quarter turns (space limited) and 1 a half turn, alternating between them to keep them even. Once the distance between the front and back bracket was close to touching, the bolts obviously became harder to turn, but still relatively easy with a tiny allen wrench. Then the inner one became too easy, and I knew it was stripped. Considering a bracket is supposed to be clamped tightly to secure objects to rounded tubing, this is an obvious flaw. 2nd bracket I installed with much more care knowing how soft the bolts are. Advice for the manufacturer: Steel bolts, different sized mounting hole options or at least a better description of the dimensions. Overall I'm still satisfied. And will be ordering a replacement from the mistake.

Used these mounts to hold off-road lights on my roof basket. Works very well, holds strong.

I was searching for a suitable mount for Deanli Soundbomb horn to my Rocket 3 and stumbled upon this. I couldn't be happier with it. It's solidly built and still light weight. I had to put it together and take out several times to locate a suitable position on the bike for the horn. It still kept it shape at the holes and where the screw went in, tightened and came out several times. The included rubber teeth set is also of good quality. They grip well and do not destroy the paint. The Denali horn I mounted feels like more than 1 to 1.5 pound heavy. But this mount is still holding it well after several miles of ride on bumpy roads. For the price or otherwise, this is an outstanding selection. BTW, I had to reach out to he customer care and their services was excellent. Looked like they are based out of California. Highly recommended.

Great

The product is nice looking, light weight, fits a multitude of bars, but my main issue is how easily the screws holding the two pieces together strip out when under minimal pressure. I tightened it down by alternating between the two screws until it was getting snug, and I tightened the bottom screw up until I thought it would hold tight without issue. After a 3/4 twist on the top screw (the longer piece of aluminum), it got tight and then stripped out rendering the piece useless. It was weird how the top piece stripped out with less pressure than on the bottom piece. The other bracket went in without issue. Well, I have to say customer service and getting a refund was a piece of cake. I sent an email to the vendor either on a Friday night or Saturday morning telling them I needed half of a new piece, and much to my surprise, I received an email on that Saturday. They stated they couldn’t ship out a new one due to the Coronavirus lockdown, but that they would refund my money and I could order a new one. My refund came immediately and I turned around and ordered a new set. While installing the new one I decided I needed to make a change to the other bracket that originally installed without issue. When I went to tighten it up again, the top screw on that set stripped out. Again, I did not tighten too much, it is just a lousy design to use such small screw threads on a piece of aluminum. Thankfully, when they sent me a new set, it was a pair so I still had an extra bracket (so much for using it on my kids quad for a spotlight). I don’t know why they can’t make this with a bigger screw or coarser thread so that it doesn’t strip so easily. I ended up using blue loctite on all the screws, but I was hesitant to tighten that last bracket down too much and I’m hoping it doesn’t move on me from vibration. I’d probably rate this item lower, but due to the excellent customer service and their willingness to back their product, I gave it a 3 star. The company itself gets 5 stars, they were great!

Well made mounting brackets.

Needed 1 to hold a light, works great doesnt move once tightened

Fitted my Stedi Floodlights to these great looking brackets. Couldn’t be happier.

Bought these alloy mounts to replace the plastic ones that came with the aux driving lights I installed on my motorcycle a few years ago. I was tired of constantly repositioning and tightening the lights because of the cheap mounts they came with not holding well. These are great and could be used for many applications! Well worth the money

The 5 mm screw hole threads are not usable. I need to run a 5mm-0.8 tap through all the 4 screw holes to clean out the threads. The screw could not be threaded into hole otherwise. Also be prepared to get different screw lengths. The screws that came were 12 mm long. I tried to attach this to a 1 inch shaft by using the thinner spacer - the screws were too short - needed 20 mm length screws. Otherwise the produce is very sturdy