Fix A Drawer x2

Who did not have issues at some point with your furniture if you drawer starts to wabble, distort it self and finally collapses with you swearing and moaning to the four winds. I bet everyone above 12 years old LoL.If you have any drawers that do not seem particularly sturdy this is definitely the best invention out there making your less sturdy drawers ultra resistant.I would buy reinforce all my drawers (which I did) with this little tool and trust me is a life changer.I hope that you have found this review useful, thank you.

This item was really easy to use. And fast. Instructions were not as clear as they could be. However I watched a video before hand. And now my drawers are full and opening perfectly.

These have been an absolute lifesaver. We purchased a second hand Ikea set of drawers a couple of years ago, and they didn't include the brackets on the underneath of the drawers. After a while of adding more and more items and clothing to the drawers, they started to bow. It became so bad that we could no longer pop them back into place, and the drawer below it would no longer close properly.These brackets are simple to apply. You just tighten them correctly depending on the length of your drawer, and you then use a screwdriver to get the screws through the wood of the drawer. If you have a very thick drawer and can't get through with a screwdriver, then you may want to ensure you have a drill ready for these.Once the brackets are applied, we were able to add all the items and clothing we wanted without any problem. Drawers completely fixed without having to purchase a whole new set.I would highly recommend this item if you have drawers that have bowed.

When I came across this product, I thought it was a brilliant solution to a common problem, especially at a reasonable price point.Fixing is fairly simple, if a little fiddly, however there is one flaw. The instructions state that you should turn the draw base over and then fix the brackets and straps to the draw. i.e. so the draw base bulges inwards rather than sagging outwards. This is essentially because the kit is not strong enough (in my case anyway) to bend the draw base back in to shape and hold it.However, the draws in my bed are only laminated one side, so this would meaning having the rough fibre side of the draw base staring up at you. Bear this in mind if your draws are the same.I opted to keep the laminate side up, but had to leave the draw base trapped between the kitchen cupboard and the fridge for a week in order to straighten it out a bit. So it's taken a month to fix all four draws! Even then the draws still bowed outwards slightly, and the metal brackets are so thin, they just bend with it.Overall the kit is good value, if not the perfect solution that it seems at first glance. The price is reasonable, although the kits must cost pennies to produce given it is just a couple of brackets and screws and the straps appear to be made from the packaging straps used on parcels etc.I just wish the furniture manufacturers would make these draws a bit stronger in the first place!

Oh my god. I was actually going to buy another bed for my daughter because of the drawers. I couldn't believe how easy these supports are to fit on. Even I did them without a drill. I am going to order some more for my mother in law. I'm so glad I found these. They saved me from spending money on a new bed.

Do the job ok I guess but an absolute rip off for the few bits of tat you get in the pack. You can do a far better, long lasting job for the same price with some cheap wood and a few screws.

Ikea drawers buckled underneath had been a nuisance for months. Had tried fixing many times but they always popped out again. I fitted this device to fix them. It took less than 10 minutes to do. (and I am but a feeble female - not terribly DIY gifted) Drawer is now fixed and I am very pleased with the results. A low cost simple fix that works!

Well, can someone please tell me what I'm doing wrong 'cos no way can I get the front part to screw in properly!I did the easy bit first and screwed the rear drawer fixture on - simple - then fitted the front part in at the correct 45degree angle as shown in the picture but no way could I get my screwdriver to fit in that angle and then screw through a solid teak drawer front. Do I need to purchase a screwdriver with an L-shaped end to go around the corner? So, I started the other way and unscrewed the back fitting but still cannot get the front piece to go in at the correct place and be able to screw it in. I'm relying on a hand-held screwdriver as I don't have a rechargeable one. Help please?

Cumple muy bien su cometido.

Worked out Great, used the set for 2 drawers with about 14" of strap left. Our heaviest drawers are our silverware and gadget drawers. Very easy to screw in. 3 screws attach the bracket to the inside drawer face, you simple loop the strap and connect it with another loop to the back of drawer, I kept stretching the strap until it was good and taut. 2 screws on the back of the drawer completes the set up. One one drawer actually opens and closes smoother than previous. .

100%ig um durchhängende Schubladenböden wieder zu reparieren. Hab das bei 3 Schubläden gemacht. Funktioniert einwandfrei. Und ist sehr einfach. Ist sehr zu empfehlen.

Le kit de réparation est vraiment très pratique, même si la bandelette de soutient en plastique est très rigide et qu'il a fallut plusieurs essais pour réussir à la mettre en place correctement. Le tiroir est comme neuf et nettement plus résistant.Le bémol a été la livraison, annoncée pour un vendredi et reçue 15 jours plus tard soit 3 bonnes semaines après l'achat. Quand j'ai voulu prendre des nouvelles via l'interface d'Amazon prévue à cet effet auprès du vendeur, je n'ai jamais obtenu de réponse.

Worked fantastic on my IKEA Malm dresser. Two of my drawers were sagging and ruining the entire concept. These fixes were easy to install and surprisingly corrected the issue of the bottom support board failure.