Question 1

Would this work for an Andersen Emco Storm door?

Accepted Answer

First of all, for some doors there are four hinges, so you'd need two kits. Some people have reported being able to chuck the pin into a portable drill, using it as a lathe, to "file" the diameter down using 100-grit sandpaper.  For my door (Andersen/Emco s/n 0016359096), three of the four sets of pins were intact, while one had a spring which had broken right at one pin.  The mode of failure however the disintegration of the flanged plastic collets forming the "sockets" for the hinge pins to ride in. When those fail, there's nothing to keep the pins in position and the springs push the pins up/down into the door frame and the hinges begin sagging. Andersen won't sell the simple, cheap, poorly engineered plastic collets, but they measure 3/16 ID x 5/16 OD x 1/2 L. I found bronze versions of these on ebay, but before that, I came up with another solution. Noticing that the hinge pins themselves were composed of a 5/16 ID shoulder (to fit inside the door channel) stepped-down to a 3/16 OD pin (to fit inside the collet), I found a #8 flat washer fit the pin nicely.  You have to remove the door/hinge-rail assembly from the frame, and then working one hinge at a time, remove the hinge screws from the door, and then rotate the frame over to reveal the door channel that the pins and collets fit into. Using an "appropriately sized wire bent at 90 degrees", insert it through the collet and press the pin, compressing the spring until the hinge pops out. Slip an appropriate number of flat washers onto the ends of the pins to fit the gaps between the hinge and door itself, re-compress the spring and pop it back into place. (Where a collet was still present and in good condition, I added one washer; where it was missing I added two.) In cases where the door channel had widened from sagging, I closed the gap back up by squeezing it with pliers so the washer had good support.  I was still worried about the hinge with the broken pin. Although I put sort of got the pin back onto the remainder of the spring, I didn't trust it, but I addressed it by exchanging its position, at the top of the door, with the 3rd one down.

Question 2

will these work on a emco 100 door?

Accepted Answer

There are no cross references for manufactures on this item.

Question 3

i need the hinges t go with the crls storm door hinge pin were can i get them

Accepted Answer

There is no cross reference for parts that go to a certain manufacture. You may wish to review item # K 5142's line drawing at the top left of the web page so you can compare it to your hinge.

Question 4

is this for repairing six hinges?

Accepted Answer

I would say no. The kit I got came with 3 springs, 6 bushings, and 6 pins. That's enough to do 3 hinges.

Material	Metal
Brand	PRIME-LINE
Product Dimensions	0.62"L x 3.81"W
Finish Type	White
Mounting Type	Track mount
Unit Count	1.0 Count
Global Trade Identification Number	00049793051318
Manufacturer	Prime-Line Products
UPC	049793051318
Part Number	K 5131
Item Weight	0.32 ounces
Country of Origin	China
Item model number	K 5131
Is Discontinued By Manufacturer	No
Size	3 Pack
Color	White
Finish	White
Item Package Quantity	1
Number Of Pieces	3
Included Components	Spring and 4 tabs
Batteries Included?	No
Batteries Required?	No
Warranty Description	Goods are warranted against manufacturing defects for 1 year. In no case is Prime-Line responsible for user related damage or damage incurred during installation. Warranty is void if products are subjected to abnormal conditions, misapplication or abuse.

PRIME-LINEK 5131 White Storm Door Hinge Pin Kit, Croft Storm Doors (3 Sets)

细节

描述

规格

有问题吗？看看别人问了什么

常见问题