3D Printer Filament PLA White Color 1.75mm 1kg (2.2 lbs) Dimensional Accuracy +/- 0.05mm. 3D Printing Filament Bought to You by 3D4USE.

This stuff does not like to print on anything but blue painters tape without heating the bed. That being said, if your printing with a Makerbot or another printer without a heated bed, that is a non issue. After i got it dialed in, i had no issues printing with it. Next time i am going to go for Hatchbox and see if it makes a difference.

So unlike many of the comments on here, I do print a LOT (4 rolls a week). Initially i thought this was a hatchbox re seller, which was what i was looking for. But after printing the filament for roughly 12 hours I can confidently say this is not. Here are the issues I have experienced with this filament.1. I have had 2 clogs so far. It seems that the diameter is not very consistent, or perhaps it was sitting in a warehouse for an extended period of time.2. It doesn't flow consistently. Parts came out looking faded and some sections were obviously under extruded.3. It requires a lot more heat than other brands I use (Hatchbox, Gizmodorks, Esun...). I have to print this at 205C+ (while the rest are amazing at 195) for it to flow well, leading me to believe it is not very pure or something.Overall, I don't recommenced anyone who relies on their printer to purchase this filament. It just isnt consistent enough and frankly is just inferior to everything else I have tried. A better and cheaper alternative, which I have purchased tens of rolls and never had a problem is Hatchbox. In full disclosure this is based off one roll, so it is possible that mine was a Dud. If the manufacturer wants to send me another roll I will test it and correct this review I did in fact receive a bad roll.

It's okay. Prints aren't as great as they are with other filaments

First test print was good, that print was about an hour long. Each print after that it jammed my printer after an 2 or 3 hours of printing. This filament ruined 4, 16 hour prints after about 2 hours into the print job. I switched to another filament and used the same gcode and it printed out wonderfully. So that makes me believe this is bad filament if your print is going to run longer then 2 hours. This filament is going to the trash because it is useless to me, all of my prints last at least 6 hours. Wish I could of found out sooner or I would of asked for my money back.

Clogged on me after 3 hours of printing

Bought this because they were out of Hatchbox. Bought 2 rolls of white because of the great reviews. Mistake. Ran through my Hatchbox white (about a roll a week) and immediately inserted and calibrated this. 3+ ROLLS of Hatchbox in February without a single failure. This stuff? Very first small print job (printing 32mm ball-bearing hubs for this filament) and the job failed. Not a spooling issue. Clogged print head. Haven't had one of those in about 6 rolls of filament. Cleared, bumped the temp up to 205 and tried again. Failed again. Clogged. Cleared it, pulled out some Hatchbox and printed the 2 hubs. Perfect. No problems at all. Switched back to this stuff, inserted newly printed hubs (with ball bearings) and tried to print another set. Failed. 5 failed jobs out of 6 attempts and the one job that did complete was unusable because filament didn't flow consistently. I've had this filament for about a month but it was stored in the vacuum sealed factory bag inside another vacuum-pack Ziplock bag with about 6 2-ounce bags of Silica Gel inside a sealed storage box with 20 other rolls of vacuum-packed filament. (I know about moisture...) Of course, my return options for the one unused, still sealed roll expired yesterday.If you are inclined to buy this filament, it is slightly more yellow than the Hatchbox white, much more yellow than the Argos white but not quite as yellow as the Solutech Real White. (I really wish everyone would use Pantone or web colors to define color...)I hate bashing filament companies, but I can't recommend this.

Not sure what the fuss is about...a lot of negative reviews in here about this product, but I have been running this spool for about 30 hours now and it prints great on my Monoprice Maker Select. No problems with poorly wound spools, jamming or inconsistent filament diameter. I will be ordering more of this same filament soon.

This is a pretty low grade filament. The width varies a lot from the specified 1.75mm. Also, the filament likes to break if you leave it sitting in your extruder between prints. The very slight constant pressure at the bends causes it to break.I only give it 2 stars instead of 1 because when you get it to print, it works ok for me. As long as it doesn't cause your extruder to jam due to the width variance anyway.