16.4ft Daylight White Led Strip Light Kit with adapter

I connected this to a Sonoff switch, which if operated via my Alexa. Sonoff Wifi Switch Wireless Remote Control Electrical for Household Appliances, Compatible with Alexa DIY Your Home Via iPhone Android App (Sonoff Dlu) The light is very bright. I installed it in my kitchen as under counter light - it is very good. The Sonoff is a binary - it is either on or off, there are other switches available to give you brightness control - and you don't have to use any wifi connector! You can simply plug it in, and unplug when done. This is excellent under counter lighting, and I will also be using it to light some of the closets around the house, and some of my garage shelving. The white is much brighter than the white option on a color roll. The light as a sticky back to it which will stick to almost anything. Making installation a breeze. For the price, this is amazing, and so many options. Using an Arduino I am making one for the bathroom that will come on when it senses movement, then switch off after 10 minutes. The lights will go under the vanity, and will light the bathroom enough for a 3 AM visit, without leaving you blinded by the lights! You can cut the tape at any point. You can then use jumpers to place the next run around a corner or over a gap. With basic skills, you can extend those wires as long as you want them. You can also start another run with a 12v adaptor. Again, some basic electrical skills needed for that.

This light strip worked well on my car lift, super bright at highest adjustment and the dimmer settings were nice. These are rated for indoor but purchased anyway for my garage. Sadly they only lasted a couple months probably due to extreme cold and heat fluctuations this year. I would recommend these for indoor and I’d buy these again.

Bought it to light ip my work area. Works great.

Bought this as a Lightning Deal for $12. I'd seen these for a while but finally decided this was a good option to try. It arrived very quickly. Usually these gadgets get tossed aside and forgotten, but I decided to try it out. I plugged the power adapter into a switched wall outlet, ran the cord up the wall, and used that as my starting point for sticking up the strip. I wanted to go without the dimmer but I found I needed it in order to reach even my relatively-low ceiling. Even then I had to have a couple inches of the lighted portion hanging down. That would probably be the one complaint I have about this product. I used a cable clamp to provide some strain relief in the hope that it will prevent the strip from being pulled down by the cord tension. I used the full length, uncut. Be careful pulling the paper backing away from the strip; if you peel it incorrectly it will take the adhesive tape with it, then it won;t stick well at all. I recognized this and was able to correct it before getting far. I peeled away a section at a time, about 1~2 ft, working across the wall. It's sticky enough that I didn't need to clean (i.e., alcohol-prep) the surface, but it wouldn't be a bad idea to brush away cobwebs or dust. Once it's up,m it seems quite strongly attached. I've only had it up for an hour or so, so time will tell. I wish now I'd gotten a longer one so I could have gone all the way across the room, but this strip covers the majority of it. I'm quite impressed with the brightness overall; it seems to light up the room better than the two wall sconces. I have them actually facing down, so it doesn't project across the room as much as it could. The photos make it seem brighter and warmer than it actually is, but to my eye I can tell a nice difference. It won't completely light up a room on its own, but it does at least provide substantial fill light. I only wish I'd paid more attention to the temperature color. It is 6500K which comes out slightly bluish, and maybe not as bright as if it had been about 4000K-5000K. But ya get what ya get. Definitely getting more of these for some other rooms. But it's limited in that it needs to be near an outlet. I would love to hardwire it to a 120V light switch but that's obviously not feasible. UPDATE 11-Jul: I've had these up for over a week and I still like them. They maybe don't seem as bright as my initial impression, but still a nice fill light. What I do like most is that they are still holding strongly to my ceiling, even in hot & humid conditions. These have genuine 3M VHB thick-film adhesive. I'd bought a couple other strip rolls from other sellers, thinking they would be the same, but they use "ME" adhesive (with a logo meant to look like the "3M" logo) which is thinner and not nearly as sticky. So I'm buying at least another roll or two of the LE product, for when I want to stick the strip facing down or vertically. Be sure on these LE strip to only peel off the paper backing, NOT the adhesive tape itself. I also have been doing more research on the connection methods for joining multiple strips, splicing, tee-joints and corner joints, all without soldering (because I can't solder to save my life). So when I get more of the LE rolls I'm planning on extending this light almost all the way around my den. I also learned a bit about LED drivers which can be hard-wired to 120 VAC and provide a 12V DC current in different wattages. I'm thinking I may take down one one of the wall sconces, hardwire a driver, tuck it behind a wall, run the output wire up to the ceiling, and thus have a cleaner installation, dimmable lighting, and sufficient wattage for the extended length. UPDATE: I decided to downgrade 1 star as I find this strip has a flimsy backing, which makes it more difficult to work with when connecting strips together with the various push-and-snap connectors. (I find the other brand to be more rigid and easier to push in.)

I bought this to help fill up remaining space in my three-way vanity, dresser mirror my only regret is not having found this one first and got in the bigger size and to have only one remote for everything. This is a great product very bright. Since again this is to fill up the remaining space I was able to go around twice with the lights… easy to install, and I love that the lights are dimmable option and a remote if you choose to buy it. I recommend if you’re unsure to get the longest length and adjust as needed. Instructions are easy to follow. A little extra info I’ve had it for almost a month and there’s some days where I have it running all night and I’ve had no issue whatsoever.

I searched for some time for a manually dimmable LED light strip for ambient lighting around the perimeter of our living room. I wanted to be able to set the dimmers where I wanted them and then use an Alexa enabled wall switch to turn them off and on from the wall or through Alexa without having to mess with dimming level each time, and these were perfect. The picture shows them during the day time on the little shelf around the perimeter of the room I built just for this purpose. It's very bright in the room in that picture, the shelf area is painted in bright white eggshell finish, and the shelf is 8-ft in the air, but the glow from the LED lights are clearly visible. The lights seem to be well made and I ran into no troubles installing 4 sets of them. The 3M tape is very sticky, so be careful what you touch it to, because once it's stuck, it's stuck. I had one place that I tried to adjust and the tape pulled the paint off. LOL, I was a lot more careful about placement after that. The set comes with little plastic clips that can be used to hold the LED tape in place and I kept them, but so far I haven't seen the tape starting to peal loose any where. If you only plan to use white light, this is a great option at a great price. I'll probably order a few more sets in the future now that I have a better idea of the kind of lighting I can do with them.

I bought two sets of these. One for my closet, and one for the back side of my desk. 1. The closest. I ran the entire length up, over, and down the inside of the closet. Coupled with a wemo switch Amazon will turn it on and off for me. 2. These are super bright, I made the mistake of standing inside the closet when first turning them on. The desk. 1. 16.4 feet is a fantastic amount of lights to run your desk to, making corners with these lights are a little tricky but not bad. Sometimes I felt the sticky backing was on too tight when trying to get to it, and thought the lights would rip. They did not, so they are very strong. 2. I made the mistake AGAIN of sitting behind my desk when turning on the lights for the first time. Surprised I am not blind. Bottom line is, they stay on, they are bright, they stick, and I have had zero problems with them. I would absolutely recommend for anyone to just pick them up, and find a use for them. They add a lot of light, and stretched underneath a counter top or for a workstation these would work great.

I'm going to start off on a positive note and say that the lights themselves work excellently and the brightness is very adjustable and the length of the wire is more than adequate for my application. Now comes the issues that I found that you may need to be aware of if you are going to seriously consider this for most applications that would apply to this. The first major issue I came across was when I was peeling the backing of the LEDs themselves in order to begin using the adhesive to stick to my application. It seemed that the backing took a lot of the adhesive from certain parts of the LED strip with it making the strip itself unable to stick to the surface of glass that I needed it to. Luckily the kit did come with some plastic tabs that had their own adhesive but that adhesive on those tabs was fairly weak and in my application I had to cut them in half in order for them to fit at various points as seen in a few of my pictures. It solved the issue but now that I have tabs and random locations it is a bit unsightly. As for the dimmer switch, normally it dangling would not be an issue if it weren't for the poor adhesive strength of whatever managed to stay on the LED strip and that of the tabs themselves, so I had to use velcro that I had on hand to anchor it so that the weight of the dimmer switch did not peel back the LED strip over time. It's unfortunate that out of the box I had to do so much just to make it work I am considering purchasing another strip that has Superior adhesive quality just so that my application remains seamless. But for now this will have to do, as you can see in one of my pictures the light is more than adequate at its brightest setting and can be dimmed further from that for comfort and can be also turned off from the dimmer switch entirely. I would have highly recommended it if it weren't for the problems with the adhesive, frankly I feel like I am being very generous with my three-star rating. I hope this information is helpful when considering purchasing this product over others.

Great item. Works exactly as advertised!!

These lights were exactly what I needed. They were quick to install, and I love that they use a dial instead of a tiny remote—those never seem to work right for me. The brightness is super easy to adjust and the daylight white color is perfect—not too yellow or too blue. I paired it with a wireless outlet remote so I can turn the lights on and off without reaching for the dial. It’s a great setup for my trailer bedroom, where the ceiling lights are too harsh at night. These create a much nicer vibe, and I actually enjoy hanging out in the room now.

Decided to use LED strips as lighting in my small livingroom and decided to try these LE LED Strip Lights, 16.4ft 12V Dimmable Strip Lights, 6000K Daylight White, 300 Units 2835SMD LED Tape Light for Home, Non Waterproof, Power Adapter Included found here: https://www.amazon.ca/gp/product/B00MHLIFO8/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 This was a little of a test as I never really player around with LEDs very much, I bought 2 while they were on sale, both little boxes came in one amazon box without wrap or anything, both work fine all LED are good. I am thinking of getting a channel with diffusing cover to put along the ceiling and these strips inside them, it should work fine since they are so bright. I got this white only dimmable strip as it mainly to replace lamps since there is no native ceiling lights in this livingroom. For now I just stuck the LED strip right to the stucco ceiling and they are holding on just fine though I did add a piece of packing tape (wide scotch tape for packages) to hold the dimmer in place in the corner which takes weight off the sticky strip behind the led strip. For the sticky strip while it sticky enough if you are not careful when peeling back the back paper you can actually pull the sticky right off the strip, it was fairly easy to tap push it back in place. That's why I gave the adhesion 3 stars for this issue I had. That said if you stick it to a plain flat wall it should stick really well and you could most likely lose some paint when pulling them off. For my stucco ceiling however is was pretty good! I included a small video to show how bright these are, looking forward to next year when I repaint the whole apartment as I will more than likely add in some LED strips here in there as pure white lighting and RGB music reactive one's in some places. These btw should work well with led channels as they are so bright! Will update if I have issues but if these last say one or two years I will be very happy considering that these in the video is only one roll of 16.4 ft and cost under 20$ CAD. Channels like this should work fairly well: https://www.amazon.ca/dp/B072MGVK9F/?coliid=I2PGLJA1HW4YMS&colid=1QRZZHRWEM46D&psc=1&ref_=lv_ov_lig_dp_it The power supply wire and more importantly the dimmer wire should be longer. For a nice set up you ideally want more reach for the dimmer so you can control better where the leds themselves start, would have been nicer if the led were only along the ceiling instead of coming down the corner like you see in the video but that not possible as is due the the dimmer wire being so short. btw there was no remote control with these ones.

I installed this kit under the hutch on my desk at work. The area under the hutch was quite dark, so I installed the LED strip along the front edge so the it was hidden by the door. The kit puts out a lot of light, and it made a huge difference to my desk, I'm extremely pleased with the results and plan on installing more of the light strips. Installation was super easy. First you identify the area you want to stick the tape to, then clean the surface with soapy water and wipe dry. Then figure out the length you need and cut to size with scissors. Next, you peel off the backing tape and stick the strip to the surface, making sure the put pressure on the whole length for good adhesion. Lastly, you plug one end of the white cable into the LED strip and the other end of the white cable into the power inverter. Then just use the remote to control power, brightness and flicker mode. This LED strip gives off a warm white light that I prefer and is so bright for my application that I usually leave it at 50% brightness. I had compared this kit to other LED light kits at local stores and this one was one third the cost, so it's a great value.

These are easy to install and provide great light under the counter.