DARKROCK EC2 Black ATX Mid Tower PC Case, Type-C Ready, Supports 50 Series Graphics Cards, Tempered Glass Side Panel, up to 8 x 120mm Cooling Fans & 1 x 360mm Radiator, 1 x Pre-Installed Fan

You literally won't find a better case at this price point. Absolutely terrific value. It's not much bigger than the case I replaced, which was about the same price when I bought it 10 months ago, but everything is just structured better, and the metal doesn't feel super cheap. There's more room for a bigger graphics card (340mm as opposed to my last case's max of 280mm), so there's plenty of space for upgrades. Cable management was a breeze with the abundance of holes and openings for cables to go to all the right places on my motherboard. Also, there's plenty of space on the rear side of the case for cable management, with more than enough cable tie points. The PSU shroud is nice and roomy as well, with an included hard drive bay tucked inside, which I appreciate, as my last case did not include one. The shroud also allows for even better cable management, especially if you're using a non-modular PSU with extra cables that you don't need. I just bundled them up and zip tied them together and tucked them away, allowing my case to stay fairly clean and open for maximum airflow, while also not making me worry if I would be able to get my side panel back on without a fight. The swiveling tempered-glass side panel that is fully removeable is a nice touch. With the mesh front panel, bottom and top vents (with dust filters; the top filter being magnetic), and rear exhaust, the case feels practically open for lots of air flow. As far as noise level, as with any mostly-open, high-volume airflow case, it strongly depends on your setup. With room for up to eight (8) 120mm case fans, or six (6) 120mm fans and two (2) 140mm fans (top vent), there's lots of room for efficient cooling. But if you're like me, you don't care too much about the noise, as you tend to tune it out when you're immersed in an intense gaming session. So, I have my GPU switched to performance mode, and my case fans are set to keep things nice and chilly, so it can get a bit noisy at times, but again, nothing that really bothers me too much. If you have a dual-BIOS GPU set to quiet mode, and have your fans fine-tuned to perform at maximum efficiency with minimal noise, the openness of the case, while creating the possibility for more noise exposure, also allows for plenty of airflow for efficient cooling, allowing your fans to keep things moving at a nice, low dB. Overall, it's a solid case. As stated at the beginning, you won't find a better value case for the price.

DARKROCK KILLED IT! Great case great great great for the price, comparible to a $150 case with the features it has. Love the hinged swivel tempered glass door with magnets, super tight look, great front panel support for USB c, tons of fan spaces, I do recommend if you've got a lot of components filling this up tho and you've got a lot of storage requirements, try and make sure to use ssds they will allow you to fit a lot more. Zero complaints about this case, there's even rubber under the PSU so it doesn't rattle, great touch.

Fantastic quality case. Super easy to take apart and install your components. Cable management isn't the best, but for this price you're honestly not going to beat it. Willing to bet anyone with good cable management skills will properly have zero issues with it, but you're not going to make anything super aesthetic. Case has plenty of room, fits my RTX 2070 with plenty of space, would have no issue with a 4070 TI Super that I use in my other system. I'm actually thinking about upgrading my old case for my main PC to this one as well. It looks really nice and mature, looks like it belongs in an adult apartment and not your teen gaming bedroom which is also a huge plus. It's good quality metal as well, doesn't seem like it would bend easily and get damaged unless you're royally clumsy. The only thing keeping this from being 5 stars is top fan attachment is a bit awkward and the only place i had difficulty installing anything. Drive bays are also another plus, designed to ensure you can easily pull drives in and out without having to remove a bunch of components first.

Package arrived without issue (all the way to Fiji). Normal styrofoam was used with single boxing but no damages. The case is a decent budget case (with 1 each usb2,3 and c front ports) and comes with a rear exhaust fan which is nice (i replaced it for aesthetic). Side glass is sturdy and hinged which is also nice. Fits 06 fans (used corsair rgb 120s) 3 front intakes, 2 for upper exhaust and replaced the rear case fan with another corsair for exhaust. There is nothing wrong with no rgb/argb but this was a gift for a friend so spruced the build up with rgb (but really hate the icue software). Am not into rgb (no rgb is the norm) but gotta admit it does add personality (mentally) to an otherwise all black case (used white static lighting at its dimmest which makes it look kinda like the b/w superman logo aesthetic). Can fit a 3 slot gpu comfortably but do consider a 90 degree adaptor for clearance from the glass panel. Airflow is very nice and airy, no inner dust guards (top one is a magnetic mat only so its nice) and temps are good (idling in 30s celcius and 60-70C under loads...in Fiji's hot December room temps) (specs: msi mpg edge wifi ddr5, 64gb vengeance, 13700k, dc-ak620 aircooler, wdblack sn770 1tb and another crucial 2tb ssd with a stock 10gb 3080). All front ports work and cable management takes some time but no bulging of the side panel with decent cabling/zipties etc. Would buy again as Fiji retailers don't have any (all over Fiji) tower cases at all with front usb c ports (the msi mobo would've been a bit of waste without front usbc). So far no issues from my friend and I hope this build lasts him a decent number of years (the refurb optiplex we got gave up after about an year). Overall, a decent product and vinaka to retailer.

So I decided to rebuild my old PC and I bought this case for my new PC. It looks beautiful and it's very easy to work with. I love the way the glass door simply opens with a simple pull ribbon since it's closed magnetically. There's plenty of room in the back panel for cable management and lots of room in the front if you want to install a few 120mm fans. I got 3 of them and placed them on the front and they work beautifully. Thanks DarkRock for making a good quality, yet affordable case.

I really like this case. I love how easy it is to open the side and how it is also easy to remove the side panel if needed. It's lightweight and meets my needs. I currently have an ASUS B550-M and Gigabyte RTX 5060 Ti 16 GB card installed along with 5 extra 120mm fans with plenty of room and everything stays very cool. Great case, highly recommended.

I haven't done a build in a while and was looking for an inexpensive case to build in. Primary considerations were a small case, good air flow, flexible air/water cooler options and one with multiple USB 3.0s on the front including a USB-C connector. I also needed 160mm of cpu cooler height. MB = MSI Z790 MAG Tomahawk Wifi. Nice to have: Screwed in slot covers! Seems like many inexpensive cases have the stamped in covers that once you twist them off you can't put them back and worse yet, leave a nice sharp edge. Air filters, top and bottom. Not a single sharp edge to be found. Easy remove front panel. Wish it had: a nice removable magnetic filter for the front fans. A removable top so I could have more easily got to the CPU power connectors and top mounting screws for the motherboard. Taller feet. With this case sitting on carpet the bottom air intake for the power supply is almost totally blocked. My case arrived in perfect condition. No dents, dings, cracks and no scratches. 6 mb standoffs were mounted, 3 in the parts bag needed for the full ATX MSI mb I used. The holes all lined up. I ended up with lots of extra screws presumably for drive mounting and fan mounting. The build was a very easy. I removed the HDD mount box (easy to do) to plug in the Modular power cables and used that area to stuff all the excess cables. Keeping the flat cables flat as they travel across under the mb gave them plenty of room. The front mount cables all easily reached their destinations on the mb. Added 3 older 120mm Scythe fans to the front, plugged in the video card and I was done. My storage is all nvme SSD mounted on the mb so I didn't have to mess with mounting SATA or HDD devices. Final testing, all of the front panel (top) connectors work, USB and audio. Switches work (PWR & Reset). I'm happy to recommend this box if it meets your criteria.

When The case arrived, I was pretty satisfied with the price and the look, When I tried to build in it there were things like no wire passthrough holes above the motherboard making it hard to cable manage, and the holes being just small enough to make it a pain to wire, but besides that it was golod enough for the price, however Every Single Screw that came with this case are not only horrible, they dont work. Every motherboard screw snapped instantly from being screwed in, and not only that, the screws on the back that hold the back panel are so tighty allined, once removed the damn thing was slighly crooked forever. Lastly the screws for the powersupply panel were so bad that tightening them left it shading and rattling, so I had to replace almost every screw besides the backpanel where I just srewed them so tightly that thing aint moving anymore. Its a decent case witha decent look, especially for the price, however id reccomend you buy extra screws or have some on hand, and have REALLY low expectations, especially cause the holes on the front dont protect from dust, AT ALL.