100 FT Sewer Jetter for 2.0-2.8 GPM Gas Pressure Washers-Flexible Steel Braid

This thing is unbelievably functional, i wish i got this years ago. Basically, this is a self powered umbrella that will scoot itself down the drain pipe with a jet in the front o cut though any muck that it might encounter. This also makes it vastly easier to get to go around 90's and such, all i had to do was pull it back a few times and let it go and it'd get though anything. The ideal is if you can go uphill, so for me i have a clean out near the septic that i used to enter the pipe. Once i put it in and had it facing the right way, i pulled the triggers on the pressure washer and it took off like a bottle rocket... I was not expecting it to be so well self powered, but i was super happy with it. Once it slowed down for a distance (for me, this was it going though grease) i started pulling it backwards, in this way it operations like an umbrella that you put it and opened and pulled out, with the main jets pushing it backwards. It took a completely clogged 4 inch pipe, full of grease and nastiness and made it spotlessly clean (based on my drain camera). I'm SERIOUSLY IMPRESSSED. Now, we can go over when you cannot start from downstream, as i had one pipe, which was the most clogged that i simply couldn't get to from downstream. As before, no problem poking a hole though it, and the water instantly started flowing once it did to, but i wanted a spotless pipe here too, especially since this one was the worst. I did the same thing with pulling it back, and i was able to pull out most of it though the cleanout. There was a section that was past the 90 degree, where i didn't expect that this would work, so i let it go past, then released trigger and pulled it back, and went back and forth several times. This cleaned the pipe as well as the downstream way, it merely took longer because you have to let the water carry it with gravity.. I checked further down the pipe and the grease didn't get stuck further down, so this will work perfectly well if you can't start downstream of the clog, it'll just take a bit longer to clean up that way. In short, this is best tool I've ever bought (in regards to how it worked compared to my expectations). The only down side is that i'm now irritated that i didn't have it many years ago!

Easy to use. Cleared a light clog I had in our main sewer line. Used a camera to check after and it really did well at cleaning all of the piping. I used the 100’ line with a 3400 psi pressure washer. The snake pulls itself down the line so it’s easy to know when it hits something.

Wow, this beat the auger and water hose and totally cleaned my main drain line that collects the kitchen sink, bar, utility sink, washing machine, shower and commode. It found the backup because it advances forward with jet propulsion. Then it destroys the clog with amazing force and then goes much further and will clean the whole length of pvc as it advances and you get a better result than the auger. I used a clamp on my pressure washer gun trigger and unraveled and manipulated the hose in the drain with my hands. Once the drain quits pouring out your end, keep advancing the hose and clean the whole length. It works very quickly and you should be prepared before you start.

This actually worked! I have a 3300 psi and 2.4 gpm pressure washer and I have the 100 ft snake. I tried to clear the line with my 75 ft Ridgid snake but it wasn't long enough. I hired a company but they couldn't get their larger snake in so they used their smaller 80 ft snake but still didn't clear it. Then I rented a snake that could go to 200 feet but around 100 feet it hit a stop. I'm not sure why the snake didn't clear it. This jet hose cleared it around 85 feet. It took awhile to learn how to use it. When it would hit a stop, I would rotate the hose to get it around the corner or pipe transition. When it hits a plug of stuff, I would let it go in some, then pull it back out a bit, then let it go in some more. That seems to help break it up. It is nice that the snake will actually flow in to the pipes on it's own as long as it doesn't hit a blockage. We had wet wipes and roots in the drain. The problem with this snake is that it uses water. So we had to collect the nasty water in buckets while trying to clear it. I have some gutter drains that I want to try this in to clear them.

Pros: it worked and I saved a lot of money. Secondary Pros: Hose comes with two power washer fittings and cleaning tool . Made in the USA at least that's what the label says. Cons: 1. Requires a Power Washer 2. Snaking ability limited (toilets). 3. Grossly overpriced 4. One nozzle. Requires a wet dry vac for the murphy's law mess you will make in the kitchen. Would I recommend? Yes! Why? I live somewhat in a remote area. Having a plumbing service come out would cost more than this hydra jet and I already have a power washer. And, this is important, I have the tools to unclog this or another drain if need arises...think I'll move first. It will not snake through toilets, etc. Mine was a kitchen sink 1.5 in diameter and 39 feet to the common pipe which included one L and two 45 bends. I bypassed the p trap. BTW, have a wet dry vac close at hand for when water burbles over pipe into kitchen until you clear the clog. This hydr jet propelled itself (once past the L section) to the clog (at about the 32' mark) and with back and forth motion until I felt the clog give way and the jet began moving forward again. I went up and down a couple of times and drain now works like it should. YouTube videos are informative. The 100 foot option is good as you can leave the noisy power washer running outside the house.

The nozzle came off and went down the sewer. Contacted manufacturer but replacement wasn't available.