hunhun 10-Pack 3.3ft/1Meter U Shape LED Aluminum Channel System with Milky Cover, End Caps and Mounting Clips, Aluminum Profile for LED Strip Light Installations, Very Easy Installation

High quality product, low profile, which was great dor my application. Smaller screws included with the set really proved useful.

I used these diffusers in two cabinet light installations. The channels are easy to cut. I used a grinder but a hack saw, circular saw, or chop saw would work well too. On one of the installations, I used double sided adhesive tape to secure the channels under the cabinets and used about a 1" piece about every 6 inches and that was plenty to secure the channels. On the second installation, I used the clips that were included with channels, and those were even better.

Really impressed with these channels, clean machining, nice plastic, easy to assemble, light weight, able to use 3m two-sided tape to mount, hod great. Everything fits together precisely and covers go in smooth and tight. not movement. All the parts need included. Would recommend and buy again. Nice aluminum feel to each channel.

I have purchased this item on three occasions, easy to use and provides a professional finish. Exceptional customer service in answering question on replacement parts.

Good straightened extrusions, well fitting diffusers with peel off installation scratch protector, well fitting end caps. The included metal mounting clips work much better for me than the plastic ones offered elsewhere. The included screws and plaster anchors.round out a complete kit. I used these with a PIR (passive IR) motion detector BQLZR DC 12V~24V 8A Automatic LED PIR Motion Sensor Switch Light Lighting Delay Time 10 Seconds for Staircase , a 12V UL listed supply LPV-60-12 Sealed Panel Mount LPV Series AC-DC 12-volt 5-Amp Power Supply with LED Driver and 3500K (neutral slightly warm) 3528 120 LEDs/meter LED strips LEDMO 2835 LED Strip,600 LEDS IP65 LED Strip Lights Warm White 3000K DC12V 15Lm/LED CRI80,Waterproof For Wet Location,3 Times Brightness Than SMD3528 LED Light Strip to update our closet lighting. I also installed a PWM dimmer, but it wasn't really needed. I put 1 strip across the ceiling at the door edge and another across the bottom of the shelf the closets are more than 1m wide so I used an elongated mounting clip at the joint to keep the channels aligned. Muzata Extension Connectors for U-Shape Aluminum LED Channel, The Aluminum Channels Can Be Connected Seamless For Longer Lighting Project,20PACK . The screws for use with the anchors are longer than desirable for the wood shelf, but the ones that came with the extensions were a good length. since I used 2 sets of 2 ordinary clips and 1 extension clip for each closet, 1 set into plaster and 1 set into wood, the screw use happened to match the provided screws, I cut the extrusions using a 10" sliding compound mitre saw with a non-ferrous metal blade. Concord Blades ACB1000T080HP 10-Inch 80 Teeth TCT Non-Ferrous Metal Saw Blade . I assemble the diffuser into the extrusion and wrap it with one turn of painter's tape or masking tape straddling the cut line . The tape provides a markable, removable surface and controls the tendency for the plastic to vibrate and chip. I use the saw as a chop saw, descending slowly into the work diffuser side up. The resulting cut line doesn't need the extensive clean up that would be needed if a wood blade is used. The tiny burr can be ignored or removed with a diamond nail file or miniature flat file Needle File Set (HIGHEST QUALITY 6 PIECE SET) Hardened Alloy Strength Steel - Mini Needle File Set Includes Flat, Flat Warding, Square, Triangular, Round, and Half-Round File. For those who don't have the tool, I tested making a cut with a razor saw Zona 35-550 Fine Razor Saw, 42 TPI, .010-Inch Kerf, Blade Length 6-1/2-Inch , Cut Depth 1-3/16-Inch , and its possible to get a good clean cut without undue effort. Neither a simple hack saw, back saw (mitre box), or carpenters saw will make a clean cut. If you happen to have an ingersol air powered (auto) body saw with a fine blade it will make a serviceable cut requiring minor cleanup with minimal effort, but a harbor freight air body saw has more blade wobble and will shatter the diffuser. I cut the LED strip and remove just enough of the silicone to access the solder pads and solder LED wire EvZ 20m 66ft 20awg Extension Cable Wire Cord for Led Strips Single Colour 3528 5050 directly onto the strip. but there are solderless connectors offered on Amazon.if you don't wish to solder.