INCLY Deep Pour Epoxy Resin 1.5 Gallon Kit, 2:1 Epoxy Resin Deep Pour for 2 to 4'' Pour Molds Craft, Bubble Free & Crystal Clear Resin Casting for River Table Wood Filler Bar Top Preserving Flowers

SUPER HIGH QUALITY, drying time Takes about 72 hours but its SOLID AS GLASS. Love the clarity and EASY TO MIX. I used it to simulate water. MY PICTURE DOES NOT DO IT JUSTICE. Its clear as glass.

I bought this resin for my larger molds and was thrilled that I can actually pour up to 4 inches! The jumbo pyramids that I've made have come out crystal clear and with very little bubbles. I've gotten so many compliments on the quality of my pieces. The price is fantastic for the amount that you receive. I'm really glad I made took a chance on a brand that I really wasn't familiar with. When I run out I'll definitely buying it again! I highly recommend this resin for deep pours.

This epoxy resin is definitely good for a deep pours but you have to make sure whatever you are using it on your surface is deep enough and the moisture in the area is consistent otherwise it's going to take longer to dry and you may have areas that are still wet and a second pour is needed. I purchased this to make a table and I put various wood pieces inside the table so I did three separate pours. Allowing each layer to dry before pouring another layer on top of it. It was easy to use and the curing time was pretty good as well. Do some research watch a couple of videos just to make sure you understand what you're doing I made a few mistakes. I would recommend this

This is my 5th project using this same pack I ordered. Degasses amazingly and self levels really well. Lots of work time too which brings me to my next point. This is NOT regular epoxy. It’s deep pour. Which means you can’t use it for stuff you’d use regular epoxy for and expect it to work. It will stay malleable. It will bend, twist, and seem defective. That’s not the products fault it’s the users fault for lack of research. So some of the bad reviews on this product shouldn’t have been allowed. User error. So with it not being like a normal epoxy you can’t just use left overs for small items unless you have a significant amount. And by significant I mean the item would at least need to be 2 inches deep by 3/4 of an inch wide. With the long work time I recommend mixing at least 100g part an and 50g part B and going from there. Add little by little to reduce waste. If you stick to what the product is meant for you will be just fine.

I have been using this resin for over 2 years now. I've bought cheaper and I've bought more expensive and I keep coming back to this resin! It degrees like a dream and I love the long working time! I hate when you use a resin that you have barely gotten half of the bubbles out, when it is already half cured and starts to steam as you remove it from the vaccuum pot! I've lost more of my 4 cup meaning cups that I mix my deep pour in. This resin mixes easy, pours clear and drys beautifully!!

I haven’t sanded and polished these pieces yet. The resin is easy to use. Typical 2:1 ratio. There were a few bubbles but I have a vacuum chamber and that took care of most of them. Work time was more than an hour so I took my time. I’m not the best photographer but they really are very clear. The only issue I had, was very very minor dimples in the top of the table top but that will even out when I sand it down. I’m very impressed and this will be my go to for deep pour epoxy from now on.

It is crystal clear , you don’t have to fight to get the bubbles out because it is bubble less and the little bubbles that you might get while mixing it … those bubbles will go away on their own!! I used for my 💀 skulls, the large skull is about 4.5-inches tall and the best part is that with this resin I can do it in ONLY ONE POUR!! I JUST LOVE THIS RESIN! Of course it you do a thin layer or resin it takes longer to cure, but they do tell you on their instructions so READ THE MANUAL 🥰 Zero complains! Thank you for a great product!

Horrible horrible horrible. Made 9 memorial pieces from this brand and none set. Well mixed and no issues but later after contacting them find out it won’t cure below 65 degrees. No mention of this on the product. Complete disaster. Do not buy this. Turns out like slim!! Unhappy customer. No refund either from them for loss of items used. My molds are ruined!!!