T48 TL866-3G Programmer Support 31000+ ICS for EPROM/MCU/SPI/Nor/NAND Flash/EMMC/IC Tester/ TL866CS TL866II Plus Replacement (T48 [TL866-3G] Programmer)

It’s over all performance good. We use this in a device to control A/C. After we program we want to be able to protect the program from being read. Where is this option it does not appear to be present in your device. If it is there where? This is critical to our operation.We use a pic 16c63a.ThankYouTeam3G

Jut got the ACEIRMC T48 TL866-3G Programmer, and already I brought back from the dead my Asus TX98-XV motherboard. Took the old bios chip off of the board, inserted into the T48 and found out the bios chip had 3 bad pins. I then inserted a new unused bios chip of the same type, flashed the appropriate bios onto the chip, inserted into the motherboard, and beep! It booted.

I mainly use the device to program 28C256 and 28C16 EEPROM chips and test 74xx logic ICs, and I have to say they really work phenomenally. The official software available for download is quite easy to use, with multiple languages available (I mainly use Chinese and English). The only downside is that the official software is only available on Windows; there is one unofficial command-line interface for *nix systems (search up Minipro on Gitlab), but it does not support logic IC testing.Overall, very good quality.

Much faster than my outdated eeprom reader.Supports more chips.I had to buy that one because my old would not reed newer eeprom.I can recommend it to anyone who deals with desktops/laptops repairsJust make sure to check list of supported chips before you buy it, to be ensured it will do the job.If your chip is not listed - it won’t read/write it.

Used this to program an AT28c256 successfully. Would give five stars if it had better linux support.

#1 Software.Xgpro current version v11.81 is on autoelectric (.cn) because its in china#2 DriversDrivers must be installed with administrative privileges.If you get error code 10 (cannot start the device) you need to put your computer in TEST MODE (this disabled signature enforcing policy allowing driver to install)Device MUST BE CONNECTED DIRECTLY TO THE MOTHERBOARD (some USB hubs will work so be sure to use direct connection if you are having trouble with the software not recognizing the device or saying DEMO under device status, indicating its not connected)#3 1st time use.It will prompt to select correct device.You will then need to flash update the device from the software menu.#4 USEYou DO NOT NEED 1.8v adapter if you are using 1.8v chip. It will work without the adapter as long as you select the correct chip.Not sure if auto detect works at all. I didn have much luck.

No programming software! I have tried with no success !

Pleasantly surprised at the power of this programmer. I needed to program an old style 27c1024, the 40 pin model, for my NEO GEO (Unibios 4.0). This handled it like a champ. Its fast, compatible and easy to use. The software which you have to download and is in the hybrid-English-Chinese is usable. Protip: "Back" and "Cancel" means the same thing. Let's see how long it lasts, but I'm please with it. It replaced my old ARLABS programmer.

CCS社のxxx-Xが接触不良で使えなくなり購入しました。PICマイコンの中でもマイナーな品種を使用しているのですが、それも含んで多くの品種に対応しています。専用アプリは中国のサイトへの接続と思うのですが、わかりやすいと思います。ただ、取扱説明書が中国語と英語しか無く、ほとんどアプリの画面のアイコンを頼りに操作する事になります。せっかく良いライターなので残念ですが、星4つにさせていただきます。