Scosche ICFD6BN Double DIN Radio Installation Dash Kit Compatible with Select 2007-2010 Ford and Mercury Vehicles - Complete Basic Aftermarket Car Stereo Install Kit - See Fit Guide Image for Vehicles

This fits perfectly with my head unit, you have to look real hard to even see that it isn't factory fit!

Replaced the radio in my 05 Ford F350. The dash kit worked great, clean installation with no problems, looks great.

Very nice stereo had a little trouble getting the face plate right but overall excellent stereo

I finally did an install with this kit on an older 2006 Ford Explorer. The stock radio died so I bought a Boss BV9384NV second hand as I just need something basic like Bluetooth to answer calls, stream from my iPhone, and play old school CDs. (Yup, I still have some of those!) This kit was recommended as a fit for my SUV and the Boss double DIN radio I bought. Great value as it comes with the mounting kit, antenna adapter, the wiring harnesses (I only needed the main one since I don't have a separate amp), and a few crimp-wire connectors - I had enough for my install but you may need more if you have a more modern vehicle that requires more cables being connected. FOR MY INSTALL, I had to trim the back "fins"/screw holders as they were not needed and otherwise I wouldn't have been able to get the radio through the opening. I also didn't need the spacers. Happy install!

Happy

Seems to have been washed in hot water & dried for too long. The facia was very loose in the dash opening and a double din stereo could NOT fit through. I tried one & thinking I had a dud, returned it for another. Same problem with the second. This is in a 2007 Ford Focus

Alright, so got this for my ‘11 King Ranch F350 because I was balling on a budget and didn’t want to splurge on the PAC harness - I have much better things to spend 100 bucks on for this truck than a wiring harness for a radio, but I digress. This harness does NOT have the ACC pin off the red wire to bypass CANBUS in these trucks, so you’ll need to run a wire down and splice into another ACC wire on the truck instead of this harness, unless you like draining your batteries or have the brain capacity and memory to remember to turn the radio off every time you park - I sure don’t. To save you the two hours of headache, Reddit and powerstroke forum searching and several beers I had to go through - the passenger kick panel under your glovebox in the 11-16 super duties has a wiring harness by the fuse box. The purple and green striped wire is an ACC. Plus, you’ll retain the factory radio setting of the door opening shutting the radio off, which is pretty stellar. The dash kit itself definitely leaves a lot to be desired. It’s a china special, so I wasn’t expecting a lot, but the pieces certainly do not snap together, so you’re holding the side pieces onto the front dash bezel itself, which did not snap onto the radio I got, for the record, while also seating the radio in place, and getting your screws set, and getting the radio lined up and aligned correctly. Definitely would’ve returned it if I wasn’t so dedicated to just getting the darn thing in and installed, but it stays snug once it’s screwed in, and it looks fine as long as you don’t look at it too closely. For the price, you get a decent amount. The crimps are good (you’ll need more than they give you), and it does the job. If you’ve got a first gen 6.7 and you’re using a china special radio, you’ll learn a few new curse words doing this install with this kit though, that’s for sure.

Kit variado para adaptar el reproductor de tu auto si este queda pequeño en el marco. Menos mal que lo encontré para poder colocar el mío, gracias

Buen producto muy funcional

Took a risk with it as it showed it did not fit my car, but when it was delivered it fit perfectly. You wouldn’t know it wasn’t OEM. The biggest issue is the screw placements you need to make sure your screws are in the front to be able to mount it. The tabs on the side that you need to break off need to be fully broken off or they will conflict with the metal caging inside the dash. Does not come with screws to attach kit to your stereo and use the screws that came with your car originally for the mounting to the car.

No queda, es más chico que los equipos din2, se tiene que rebajar para instalarlo, instrucciones muy pobres

gaps from both sides and holes did not line up with the DIN - Amazon honored the return

So this is a copy of a better known brand, however they failed to copy it exactly. fitment is horrible. over 1/4" gap on the outside of bezel and 1/8" on inside. If you look close you can see the gaps. Also the side slides that mount to the bezel and head unit does not click together like other brands. I used a soldering iron to melt it in place to keep it from falling out during install. I was forced to use this because the other one was held up in customs. Yes it worked, most people would not notice the difference but if you really love your ride and want things looking clean - id give it a pass. This whole project was done on the cheap and I wanted AA ACP for under 200 CAD - which was achieved. The ATOTO unit f7 wireless was used. Use a wiring diagram since you will need to use some of the no name wires (brown) on the harness for steering wheel controls, and used the white plug for the sub - The red one did not work. ( in cases where you only have 1 sub out on the deck)