Dracaena.io 120mm Copper Water Cooling Radiator, 29mm, 2 G1/4 Ports, Black

I bought this radiator because the HYTE Y60 case requires a 28mm radiator for the top of the case. This was the only in stock radiator I could find at the time. - The price is a good selling point. - As you can see in the picture, the logo sticker was crooked but easily corrected. Not something worth removing a star for. Some people might like it without it. - All the fins were straight and evenly painted. - After reading other reviews, I’d suggest rinsing the radiator first with distilled water. Some people claimed there was some residue in there’s. Personally mine looked cleaned but it’s probably a good idea to error on the side of caution like I did. - Easy to install and all of the holes lined up. - I pretty sure the distributor ships from Texas. I bought (2) different models at different times and I believe one of the orders took an extra day, ** Overall I strongly recommend this radiator. It’s a decent price compared to the competition especially when there doesn’t seems to be many 28mm available. I was skeptical of the price but I’m very happy with the purchase.

Delivery was prompt Radiator is as advertised copper tubes with brass tank caps, paint is solid quality; all of the screw holes were tapped and came with 8 long screws (for mounting the fans) and 8 short screws (for mounting the radiator to the case) Thread was G1/4 held .75 Bar for 24 hours

Large enough to deal with whatever heat your computer is producing. However with a thickness of 1.77 inches, and having to add fans to it, you need a very large case. Still it's a prime component for a great water cooling system.

good for small GPU cooling

Water block worked flawless and all the hardware included was great. Couldn't have gotten a better water block for the price.

Pro's Quality of the copper and brass is great, It operates as expected for a great price. But this is NOT a radiator for first time builders. With that said all of the below cons are a potential risk for first time builders, and or the unaware. There is nothing inherently wrong with the design, but common mistakes could occur due to finish and design choices. Con's there are some finish issues, the coating on radiator bleeds onto the threads and was sharp enough to damage fittings o-rings (these had to be deburred with a abs plastic scraper DO NOT USE METAL to scrape the thread clean you will damage the threads and cause a leak), second the included screws are not a standard screw that is used in computer cases, so don't confuse them. The small screws are too long, I had to use washers (not included) to take up space otherwise the screws would push through the water jacket and the radiator would leak. Note depending on the fan you pair, you may or may not need to exercise equal caution with the fan mounting. I used Noctua fans which are great, but I have had cooler master fans in the past which its mounting tabs are flexible. If the fan flexes it IS possible that the long screws could contact the water jacket and poke a hole as well. IF the manufacturer were to make a change, a 'shelf' under the screw area to bottom out against would make this a near perfect product. As it is, screws on both sides of the radiator could poke through the water jacket and cause leaks.

Great radiator! Worked for my needs. No leaks

Its an ok performer but the holes are not alingned properly so the middle fan is pinched and cant spin

Great quality will use again

Works like a champ. Put this into a 4u chassis for a 3960x threadripper. I'll be grabbing another of one these in the near future for my other threadripper setup

No idea how electrical watts translates to heat watts, but a watt is a watt right? If i Run 450 watts through my gpu, this rad has enough area to keep it at 50C or less. Tested by looping Port Royal until equilibrium w/ 2500 rpm be quiet fans. Soaked it for a day in 7% ascetic acid vinegar, only saw a few specks of pepper on flush before install. Packaging is good, no bent fins, comes with lots of screws.

他にも90度エルボーやホース繋ぐジョイントも注文したのだが、エルボーも直接ホース繋ぐジョイントも共に入らず、それら同士はスルスルとネジが奥まで行ってパッキンちゃんと潰せたのだが、 このラジエーターにはネジピッチが違うネジに入れたときと同じような、最初の1/8はスルスル入って急に固くなる特有の感触が帰ってきた。 ネジピッチ確認用のツールは仕事場にしか置いてないのでチェックしていないのだが、この手応えはネジの品質がどうとか言う問題ではない。そもそも仕様が違う。 手の込んだ造りに見える各画像だったが、そもそも使用が違うとは思ってなかったため注文から日がたってしまった上組み上げようと開封やら何やらしてしまったために返品もできない。せめて正確にこの商品に合うネジピッチの外径8mmチューブ用チューブコネクター2個を教えて欲しい。 この商品の接続部は真鍮、電蝕を起こすといけないので各コネクタも真鍮、無理に回せば破損しかしないので無理に締め込めず、目的の用途に供することもできない。 この後規格のタップ(ネジ作成用の工具)を調達して切り直すとすんなり各コネクタが入るようになった。 銅製ラジエターでこの値段は安いほうなので、すんなり入らない場合の為に同時にタップも購入することをおすすめする。 こちらは下記ツールを購入。どうも海外レビューでは耐久性に劣るような記載があるが、真鍮、銅、アルミ等軟質素材なら良好なようだ。 Utoolmart ねじ切りタップ スレッドミルタップ テーパタップ ネジG1/4 イギリス規格 高速度鋼HSS ねじ切りタップ テーパータップ ネジスレッド プラグ パイプ 1個入り

Came with a few dents in the fins