Glixal ATKS-04015 16X13mm High Performance Racing Variator Roller Weights Set 139QMB GY6 50cc - 100cc Scooter Moped ATV (10 gram)

Good

my moped had very little bottom end however it would go 50mph it would take forever and the wind would have to be on your back some days 30 mph tops to much wind. On trails grass topped out at 18 mph. I installed the 5g rollers now i have much more take off and i can drive 45mph even with heavy winds engine is not revving high.

So far so good. Hope they last a while

What did I use this product for? 2022 Honda Ruckus Stock 7g roller replacement. My riding routes vary. Some are stop and go if I go into downtown and some are long stretches, if I go to the suburbs to visit family and friends. Based on this mixture the review I am giving is very balanced. The elevation of road I ride is also very balanced with lots of uphill, downhill, and flats. What did I like? I did like the shipping time on this item, ordered November 8th and they arrived November 18th. Expected arrival was November 24th. The color of the rollers is visually appealing. Cool 90's style. What did I dislike? Performance: Brand new 0km/0miles with stock 7g rollers I was able to hit 68km/hr | 42.3miles/hr. My friend 6'2 210lbs was able to hit the same speed on his 2022 Honda Ruckus brand new, we purchased the same day. At 4897km | 3043miles with stock 7g rollers I was able to hit 61km/hr | 37.9miles/hr. My acceleration was quite good, however on some hills I desired more consistent powerband so I purchased these rollers at 6g. At 4897km rollers were changed from HONDA to GLIXAL (top speed 63km/hr | 39.1miles/hr). Immediately after replacing my old worn rollers I noticed a substantial power decrease with dead stop acceleration. It felt like there was not enough resistance/weight. After going for a test ride I was disappointed thoroughly. I took my usual routes and compared my speeds on flats, inclines, and declines compared to the stock rollers I had when new and when worn. The stock Honda 7g rollers when new outperformed these rollers in every measure possible, acceleration, flats, downhill, uphill, and top speed. The stock Honda 7g rollers when worn after 4897km | 3043miles outperformed these rollers in every measure possible EXCEPT top speed and downhill. This was also confirmed going for a ride with my friend who had GLIXAL 6g rollers and I having HONDA 7g stock rollers on some long flats, accelerating from a dead stop, downhill, uphill, and top speed run. Final Thoughts: Initially Honda used 9g rollers on the Ruckus when first released in 2002 had a rev limit of 8000rpm. Then Honda switched to 8g rollers on the Ruckus late 2000's and had a rev limit of 8000rpm. Late 2010's Honda changed to 7g rollers on the Ruckus and increased the rev limit to 8900rpm. The majority of feedback I have read on forums regarding the Honda Ruckus and 6g rollers were from posts pre 2010's. It could be the old setup of the Ruckus where these modifications worked best. With the increase in rev limiter by 900rpm it seems the Ruckus is able to handle go a bit faster stock and handle a heavier weigh than 6g (7g stock). ADDING AIR TO MY TIRES (Front 28psi | Rear 33psi ) gave me better acceleration than adding these rollers to my 2022 Honda Ruckus. I would NOT recommend these rollers to anybody riding a 2018+ Honda Ruckus. You are better off getting stock 7g rollers OR 6.5g rollers. *Remember, the worn rollers in the attached pictures were outperforming these rollers in almost every measure. 3km | 1.8miles difference in top speed only attained on a downhill.

I bought a brand new 2024 Honda Ruckus that stock run 45 mph. It came with 7g roller weights. I replaced the the rollers for 7g Dr Pulley slider and I find out that they are heavier than the rollers so it doesn’t work. Then I ordered 6g of Dr Pulley Slider they work but it take too long to get the top end speed. So I decided to buy 6g roller weight and, wow! It definitely work way better than the slider on the stock variator. Now I have better acceleration without loosing the top end speed. I’m 250lbs 5’8 tall so the roller weighs or Slider depends on your actual weight. Hope this help you all. Thank you