Chip Quik SMD291AX Solder Paste no clean 63Sn/37Pb in 5cc syringe 15g

Not going to pretend this is a discovery — Chip Quik SMD291AX has a reputation in the hobby electronics community for a reason and that reputation is earned. Been running this through a stencil on leaded paste reflow work for a limited board run and the results have been consistently clean across the whole batch. Paste consistency is exactly where it needs to be. Extrudes smoothly through a stencil without bridging on fine pitch pads, holds its shape between application and reflow without slumping, and the tack is strong enough that components stay put through handling without shifting before heat is applied. These sound like baseline requirements but cheaper pastes fail at least one of them reliably. 63/37 eutectic alloy means a sharp liquidus transition at 183°C with no plastic phase — you get a clean reflow without having to babysit the thermal profile as carefully as you do with non-eutectic alloys. The joints come out shiny and well formed consistently. No clean flux residue lives up to its name. Left the boards as-is after reflow and the residue is minimal, non-corrosive, and doesn't cause any issues with continuity or appearance. When I do clean it IPA takes it off without any effort. 5cc syringe format is practical for stencil work and hand application on rework. Keep it refrigerated between sessions and it stays workable for a long time without drying out or separating. If you're doing any volume of SMD assembly and still experimenting with paste brands stop experimenting. This is the one.

I've been able to use the same syringe of this flux for years, storing it in the refrigerator. I've had better results with this flux than others when stenciling. The solder seems to reflow more easily and the components stay put when using a hot air iron at low air velocity. Throw it in the refrigerator for a bit, or it will tend to stencil into small puddles instead of well-formed shapes. In my opinion, it's the best.

I accidentally bumped the batter connector off of an iPod Classic, and could not get the pads properly soldered with a normal spool of solder and looked into alternatives. It has been well over a decade that I had to solder some SMDs, so I forgot about liquid solder/solder paste and after seeing a couple Youtube videos using it I figured it is much cheaper than replacing the logic board, so if it doesn't work, no big deal. I was able to clean off the pads and put a drop of paste on all three pads and easily solder it back down with a wide tip. Since I didn't have good precision tweezers, I had a small bridge between two pins, which I was able to eventually get cleaned up. By no means meant as a problem with the paste, but just be careful not to use too much. :)

Good solder for the price of solder paste is what you’re looking for. There are definitely many choices out there for this application I can say this solder worked well for me and I can recommend it. Giving 4 stars cause I’m not sure if it’s the best, but I know that it works well for me.

As the old saying goes, "a little goes a long way". I practiced soldering using an old SMD based VGA card, removing components, solder wicking the pads, applying this paste, setting the component in place and heating it with my hot air workstation. It's satisfying to see the grey pasted suddenly flash into a silvery mercury--like liquid, and seeing it pull into the pads to form a perfect solder joint. Just a tiny pin dot of the stuff on each solder pad is all you need. Any more than that and you'll need to wick away the excess as it forms solder bridges. After I made several successful chip replacements on the test board, I tackled my expensive audio analyzer relay replacement. This paste made short work of it. Highly recommended.

works well on wires not pc boards

I have never soldered any SMD components and I've always had trouble with THT but decided to give SMD soldering a try. First resistor I soldered worked flawlessly. I ended up soldering 44 0805 resistors, 14 0805 capacitors, 6 3216 diodes, and 10 0603 resistors. They all worked perfectly using a hot air gun at 300C. Will definitely be using this product as I continue to practice SMD soldering and on my upcoming project. Will be testing it on ICs in the coming days.

This is an excellent 63/37 solder paste! I was having no end of trouble soldering some 40 pin TSSOP packages by hand. Using this paste solved that first go. No stencil was used. Just ran a bead of paste over all of the pads. Put the flash chip on, centered it as best as I could. Heated it with a reflow heat gun (330C) until the paste reflowed. Then cleaned up a few solder bridges. Worked like a charm. The included tips are ok. I would recommend getting some larger ones. The paste is a little hard to push through thin tips. Also it needs a little pressure to stick to the pads.

Perfect for dealing with computer elements and for tight places.

Heats up and flows more or less as expected, with the odd bit of solder flying off. Make sure to clean up with isopropyl alcohol after use.

I had bought this ages and ages ago but had never found a use for it. Finally did some reflow soldering and found this stuff to work amazingly. Instructions for use were clear, melt was good and final performance seems to be as good as my hand soldering. Definitely would recommend.

La pâte est précise et fonctionne à merveille... ce n'est pas un produit pour débutant car si mal appliqué ou en trop grosse quantité, ça peut créé un court-circuit... pas assez, la soudure ne tiendra pas. Somme toute, excellent produit, je recommande.

Leaves a small bit of residue but works fine.