LightingWill 10pcs Pack L Shape Solderless Snap Down 2Conductor LED Strip Connector for Right Angle Corner or 90 Degree Connection of 8mm Wide 3528 2835 Single Color Flex LED Strips

I was a little hesitant to order these based on some of the reviews indicating the products simply don't work or are unreliable. While I found the clasps a little fiddly (mainly because they are pretty tiny) and the lack of instructions an extremely minor setback, simply examining the photos of the product on the store page, it's pretty easy to figure out. I slid the light strip into the connector with the tape backing intact to make it easier to slide in and applies a little more pressure to the contacts. After I have them in place and locked down, I (very lightly) score the tape backing with my knife and tear the backing off of the light strip to adhere to my surface. The connectors work great and don't seem to be unreliable at all. No flickering, no reduction in brightness, just a great right-angle connector.

They work very well, have a nice low profile, and are easy to use. You may encounter a couple issues, which I hasten to say are not the fault of the manufacture, but go with the territory and have simple solutions: (1) Very wide LED strips may not fit into the slots in the plastic. In that case, you can easily trim the edges of the strips with scissors without losing any conductance (ie without causing any dimming). (2) Like any solderless connector, some voltage loss is inevitable where the metal connectors in the joint contact the metal leads in the LED strips, but the loss is negligible unless you have a half dozen or so joints in series. If you do, you may notice some dimming of lights.The solution is to pop open the plastic with pliers, add a dab of solder to each joint, and press the plastic back together. The lights will then be as bright as if they were connected directly to the power supply.

They seem to do the job of getting the led strip to do a 90 degree turn. I do get some flickering from time to time though. Not sure if it’s the les strip or the 90 degree adapters.

Rugged 90 degree connectors for serious LED enthusiasts. It's really an art figuring the amperage, wattage, and power supply needs for a successful setup. Dusk to dawn lighting? Remote enabled. Want to connect to a solar module? or maybe a battery solar module combo? You can do it with LightingWill LED's. Plan your lighting and win with LightingWill. Really can't recommend these LED's enough! Especially the indoor outdoor lineup. Let there be light!

This product is terrible. Probably works fine if you aren’t putting lights in channel. They slide apart easily. Four connections needed

No hassle connections for 90-degree turns in your lighting strip. The little clip flaps are kind of difficult to open since they are so small, but that comes with the territory since the part is inherently tiny. Once they are opened, simply insert the lighting strip in under the little metal tabs and flip the clippy-thing shut. Just pay attention to the polarity of the contacts on the strip. Whatever contact is on the outside of the bend on one side, will need to be on the outside of the bend on the other. If you get it wrong, the extension strip won't work and you'll have to open the clip up and connect it to the other end of the extension strip instead.

Seems like most work but some dont make contact. Not very sticky. But cheap

These work fine. I didn't notice till I was working with them a bit, but there is a right way to hook them up. There is really no need to open up all four snaps on the corner... just the outer ones for incoming and outgoing. Once you open then don't just put the LED strip on the little points and close the snap. If you look closely you should slide the strip under a little ridge/guide. Because my strips were sticky on the back, I used a small blade to push the strip on up there a bit. Then I closed the snap. Works like a charm.

These connectors work well, they open easy and contact the light strip terminals well. I had to lift the terminal very slightly to get the terminals under the contracts as they are very tight on the housing and the strip was folding as I tried to push it into place, once it was in it was secure and worked first time.

Très bien

Decent clips, seem solid and easy to use and modify. Won't work with COB strip, just not wide enough.

This is a great product. It is easy to use and made fitting LED lights very straightforward - even round corners

Little bit hit and miss with the connections which is annoying if you've made a whole set up to find they work sporadically 🙄