Straight Edge Guide XL, 98 Inch Circular Saw Guide, KMA4700

Works great. A good tip for ripping 8’ sheets- after securing it to the sheet, pick the center of the guide up a little and drop it. Like a 1/4” is good enough. Kinda like a chalk line. It has a tendency to bow a little while you’re adjusting it. It’s not much but it is there. “Snapping” it takes care of that. I still love the product.

It makes your cuts straight and true. Takes a few minutes to put it together as it comes in 4 sections. The set screws and the provided Allen wrench are a bit of a miss mach so be careful not to strip them out. It is super light but kind of a pain to disassemble to make smaller so I would recommend just storing it as the full set. The saw blade markers are awesome make it fast to set the correct line, but you have to set them left handed or right handed. They could have made it ambidextrous which would have made this thing basically flawless. It's a fraction of the cost of their tracksaw kit and if you're somewhat handy this will get you 90% there.

It works pretty well. A little cumbersome if you need to add or remove sections. But it makes it easy to rip full sheets of plywood. And the price isn't bad.

Good product. Reasonable device

I purchased this straight edge guide to replace my normal method of clamping a straight edge to plywood sheets as a saw guide. I am ripping 100+ sheets of MDF and wanted to speed up the process. Background: Hobby builder and home renovator for 12+ years. Medium sized shop space. Pros: Once you learn the clamping mechanism, it is a quick and simple process. Easy assembly (be sure to grab an aluminum level or a square to verify joints are straight. Cons: Flex in the aluminum can cause your straight edge to "bend" and your cut unsquared. Comes in 2' segments to be joined together. Saves spaces in shipping but causes a weaker bond. Bottom Line: This product is probably great in the 4' version, but the XL leaves something to be desired. If it was slightly thicker/more beefy, it would likely hold up better against the slight pressure of the saw ripping down the line. I had high hopes this would speed up my process. KREG takes feedback seriously and will improve the product, but I'll be stuck holding this segmented 8' piece of aluminum until I'm tired of looking at it.

I set up the bars that if I placed the part before or after the line (see pictures) would determine which way i'm cutting. In that, which way I measured. Facing it, if i measure from the left I wanted to have them on the left side of the line so it would be accurate, and if I measured from right, right side of line. This was due to depending on the cuts I had to make, sometimes the greatest amount of plywood left would be on 1 side or the other, but my saw always runs from the handle. It's how I set it up. The thickness of the pointer on the plastic arms is right around the thickness of my blade. It might be off 1/16 from the exact size of the blade, but not enough to make a difference when cutting plywood for cabinets IMO. I am finishing my basement that includes cabinets for a kitchenette. See picture of installed bases pre doors/countertop. These were all cut with this tool on 3/4 plywood. I used an online website to get cuts so i could purchase the least amount of plywood. Used this tool to make all the cuts. The reason for the lines is to double check my measurments. I have a tendacy to measure 3.5" at the 2.5 (opposite side of the 3) without realizing. So I'll use my T square 48" long and make the cut line and just verify that i'm not F'ing up. I also wanted to make sure the cuts were right on the line. Besides some wobble here or there when I wasn't holding it steady against the track, you could just see a sliver of line left. Perfect for how I measure/mark. I think the cabinets look good and this tool was perfect for me and not too expensive.

I bought the XL version of the Kreg straight edge so I can make cuts up to a full sheet of plywood length. Like all of my Kreg tools, this works really well. Accurate cuts become very easy using a hand held circular saw when a table or other saw is less practical. With 4 straight edge pieces that can be used in shorter form, or all 4 quickly and securely joined for long cuts, a handle and spring managed, marking, attaching/clamping and cutting becomes very easy. Finding a long enough straight edge used to be painful. Now I can quickly connect as many of the 4 pieces as needed, mark each end of the material to cut, put the guide in place and cut. One thing to consider - the straight edge saw guide includes two adjustable guides to allow marking where the cut will be, line the straight edge up then push guides out the way and cut. Easy enough, but for storing as compact as possible, I need to remove the guides and set up each time. I choose not to use the two additional plastic guides. Instead I carefully measured my held held saw - exactly 4 inches from the edge to the blade where I want to cut. Now all I do is measure 4 inches from where I actually want to cut, one mark each end of the material, clamp and cut.

This product is very well built! The pictures doesn't do it any justice. Really durable!

梱包に使われている段ボールと付いてくる物は全てとっておく事をお勧めします。4分割されていて組み上げて使う形です。組み上げに使うのは2.5mmの六角レンチでTハンドルみたいなのがあれば楽に組み立てられます。組み上げは5分もかからないです。使う際にブレが気になる方はクイッククランプ等で締め付ければブレたり動く事はありません。大きな板を切断する方にはおススメです。

First of all, the product is good, and very useful. My problem is, I did order an XL what is good for 8' lengths. But I have got 2 times 4' guide. It is good, but I can not build from it an 8' guide. I tried to contact with the seller, no respond at all. The Amazon asked me, did I get back any respond from the seller, I said not, and nothing happened since that. I needed to spend other 35 dollars to buy an extension to have an 8' guide.

Excelente herramienta

The clamping system is brilliant, well thought out,should have brought sooner

クランプを使わないで、長い直線を複数の機器で加工出来るのなら便利だと思い購入。 しかし、どんなにきつくしてもコレ単体では抑えが甘く材料によっては動いてしまう。結局は終点だけをクランプで止め加工。 発想はいいと思うが今一つ…