DIGITEN LCD Digital 0-99999 Counter 5 Digit Plus UP Gauge + Proximity Switch Sensor with Magnetic

Exactly as I needed. Works great and easily installed. Bought for my CSM.

Works well, even when the magnet moves slowly past the sensor.Price is right.Having it resettable is nice.

First, this device works as advertised. There are connection instuctions in English (simple). Battery replacement is easy although lasts a very long time. The sensor is more sensitive than they say, maybe 1/2 - 3/4 inch and that is with their little button magnet. The stronger the magnet the greater the distance. A great deal since the hall sensor or the counter is worth the price alone. The provided sensor doesn't have to be used. Any switch, of any sort, will work. It is also very nice that they include that small bracket that holds the sensor and the sensor has a long threaded neck, with two nuts, that allow adjust the distance from the magnet after installation. They don't mention but to reset the counter, you can used an attached switch or just press the pause button a couple of times. See the attached picture for my application where I count the revolutions of the rear tire of my lawn tractor (I just snapped the button magnet on the tire rim (two magnets would give two counts per revolution). It bounces around quite a bit but that doesn't phase the sensor. They provide a bracket for mounting the counter or you can use a another magnet. Just remember that this is not a high speed counter, maybe 10-20 counts per second or 600-1200 rpm and depends to some extent on the strength of magnet and sensing distance. In addition, it only counts up since the sensor can't tell whether the magnet is coming or going.

When I got this counter out of the box, I was pleased with it. It was easy to install for my application and it worked well. Three months later it stopped counting. The display shows that the signal from the magnetic sensor is coming all right, but the number of counts does not change - it shows 0000.I turned the counter off and left it for a day. Next day I tried it again and to my great surprise it began to work again. I would rate it with five stars, but decrease it to four because of this unexplainable hiccup.I am an electronics engineer with over 50 years of experience and that is why I handle any electronic device with the utmost care.Anyway, I am glad that it works again and I can keep it

The media could not be loaded. Hooked it up to the power head of our resin pump to count strokes, this little guy is a beast! Battery life so far is impressive, been running about 4 hours a day for the last month with no sign of failure. Works great with 50’ of 18 Awg wire to the Hall effects sensor.Going to purchase another one for our other pump, and would happily replace them if they ever go down.It’s just switch activated, you could replace the Hall effects sensor with a micro switch or anything. Just close the circuit and it counts.The one complaint I could have is that the power/reset labels on the front are hard to read since they’re molded into the housing and the same color, throw a little paint or dirt on it to clear it up:)5/5 worth the money.

I love these work so good durable ease to use

Added this counter to my Lee Pro 4000 progressive press to count finished rounds as they fall in to the bin. Had it all setup and installed on the press in less than 10 minutes.Instead of using the supplied magnet I used a cabinet door magnet so I could screw it to a piece of 2x4 to get the right height.Pros:Cheap - good bang for the buckSo easy to setupIt works perfectlyEven comes with an AA battery installedEasy to use power on/off and reset buttonsCons:Wires are extremely small gauge and would not stand up to movement where they screw to the counter connectors. I have mine secured with an electrical tie so they never move. Problem solved.This works perfectly. Would recommend this for sure.Really I cant see any real reason that this isn't just an awesome answer to my How do I get a cheap and reliable finished bullet counting question.

Built a system to monitor water well cycles. Used a PLC and wrote a small program to gather information and send it to counters. These counters worked great. Do not need the sensor or magnet. This device will work from a dry contact closure on the count which is an output from the PLC. Used them to show cycles and time. Now I can see just how many cycles my well goes thru in a given period and also just how long the well is cycling and pumping water. Already knowing how many gallons per minute my system pumps, I can convert the information from the counters and know how many gallons I'm pumping per cycle and how many cycles I have run. Using these counters allows me to just walk by my control area in the garage and look at the counters and see the information. I'm extremely happy with these units.