UTG 1PC High Profile Airgun Mount with Stop Pin, 1" Dia , Black

I bought myself a nice airgun with a scope (a Walther Falcon Hunter .25 cal) about a year or so ago, but the mounts that came with the gun weren't that great. It would keep getting loose, no matter how many times I tightened it. Also, since there were two separate mounts for each ring, instead of an integral 1-piece like this one, it didn't hold as well.After I installed this mount, it feels a lot more stable, and the scope doesn't slide around after getting loose, like it did with the original mount. I also like how there's 3 screws on the bottom instead of two, so it holds tighter. The package also came with extra screws in case you lose them, which is nice... I guess.I shopped around and noticed that there were a lot of mounts that were a lot more expensive, so I'm overall satisfied with the price, look, and performance of this one.Just another note... this mount is for the dovetail dimensions, so it won't fit the guns with the wider rails. I mistakenly bought a different mount that was for the wider rails before I bought this one, and so ended up wasting some money there. Always best to check what size you need first...

I knew I was encountering an issue with the scope mount for my Gamo Swarm Whisper 10x .177 air rifle. The scope would not hold zero, and my shot groups were more erratic than I could tell the rifle was capable of, so I decided to use this mount in troubleshooting. After 5 minutes of zeroing the scope, I could immediately see my shot groups tightened up both at 11 and 28 yards, from roughly 1” and 3” respectively to pellet on pellet at 11 and 3/4” at 28 yards! If you think you’re having scope issues and are the least bit curious about whether the mount is the culprit, this small dollar amount will produce an immediate result if the mount is the issue :). I can’t speak to longevity, but it feels extremely well made, all the threads were cut accurately and with quality (one earlier review mentioned that, I didn’t see that). I did use blue thread locker and I was careful not to over tighten the screws. Even before the thread locker dried, this mount tightened my groups all around. Highly recommend.

I purchased two UTG high profile scope mounts for my spring airguns. The nature of the spring-piston airgun is unique in the fact that they give a double recoil. A rearward recoil when the piston is released and a forward recoil when the piston slams into the breech. This double recoil is very hard on scopes and mounts. The UTG one piece mount is far superior to a two piece mounting system because it holds tighter to the dovetail on the rifle and the problem of lining up the two scope rings are nonexistent due to the nature of the design. Misaligned scope rings can be problematic and difficult to correct. Another manufacturer makes a similar mount to the UTG but they use 5 screws to clamp to the dovetail rather than 3 and I would think that would even be better but it costs considerably more than the UTG mount. I have not had a bit of trouble with the UTG mount moving and it has a stop pin that helps too. For rimfire rifles without a hole in the receiver for a stop pin, the pin is easily removed from the UTG mount.The UTG mount is packaged with an extra mounting screw and stop pin so in case you lose one, there is another on hand.I would recommend this mount to those who plan on installing a scope on a spring-piston, or gas-piston, airgun. I think this mount would be an excellent choice for rimfire rifles too. After seeing how well this mounts works, I plan on installing a UTG single piece mount for use on Weaver bases on my 500 S&W single shot rifle that has a tremendous recoil and I have had problems with the scope slipping in the two piece rings I use now. And you can't beat the price here on Amazon, at least I haven't found it yet.

I will be using this mount on a Hatsan break-barrel gun hopefully to "defeat" the dreaded break barrel "double recoil.Have not "fire-tested" it yet, but fit seems good and solid.

This is one seriously beefy scope mount! Machined from one solid chunk of metal, it LOOKS like it'll take all the punishment you can hand it while afield. It clamps solidly in place, And rides high enough to mount at least a 40mm AO scope...likely even a 50mmAO, albeit barely? It's length is just right for setting up just the right eye relief on your favorite air rifle too! It seems UTG did it's homework on this one? Good bluing job as well. They also include all the hex key wrenches you'll need too. Below is a pic of it mounting the 3-9x32 scope I swapped off my Winchester 1400cs to put on this Crosman Optimus for my son. You can easily see that it'll mount a much larger scope, judging from this pic...

It was used. Obviously someone tried this and sent it back. Package was ripped and taped with scotch tape. Everything was in there, fit great and it is the perfect height for my scope. I needed a pin and clamp style scope to keep my scope from walking on my Gamo and this does the trick. It’s not super high which I like but I have a fat head and this gives me maybe a 1/4” higher view through the scope vs single scope rings. I’m testing it this weekend on a camping trip. Fits nice, seems like it’s great quality. We shall see.

This has got to be one of the strongest, best designed scope mounts on the planet. It is well crafted and has a very aesthetic design. Strong mounting structure in both the scope cradles and the large, strong screws and clamps for mounting to the rifle. The scope stop pin is also well designed and crafted and the mount even comes with an alternate/backup pin in case of a bad fit. Everything that you might need is included with all the hex wrenches and extra screws.Well done, UTG!Update: 11/9/2012I have just purchased my 5th or 6th one of these mounts, mostly to replace other mounts that I have used that didn't come up to expectations. I have yet to discover any other mount designed for this usage that can approach the great design, craftsmanship and sturdiness that the UTG offers. I have NEVER experienced a problem with these mounts in any form or environment. Again; 'Well done, UTG', and thanks!

It's an okay mount. Mounted it to an AR (5.56)with a 6-24×50 scope and found the scope wasn't holding zero, thought it was the scope but it turned out none of the screws had loc-tight on them and several had backed out. Must use loc-tight on them. I've had other mounts that already had it on the screws and didn't even think to look at these.

awesome on my crosman shockwave 1200 fps keeps everything rock solid but use blue locktite on the rings and the mount all bolts i did even on reciever and the stock

Good quality

very good mount. all five star. fire arm level quality!

Instantly fixed the sliding problem from the bolt slap I was having on my marlin 795

High quality. Much better then the scope rings that came on my gun.