FastCap Kaizen Foam Sheet for Tool Organizers and Storage - Perfect for Professional Contractors and Technicians - 57mm Thickness, 2' x 4' Sheet Size, Black & White

Excellent product and a good deal based on usage.

I had heard so many people saying this was the best foam for tool boxes and so. Now that I have used it and seen how well it works I agree!! This foam is awesome!! I used it for my power tool set I bought and as long as you cut it precisely to the size of your tools it is great! Note- Some people described that the foam wasn't peeling off like it should (one sheet from another) and its true. It doesn't peel very clean, leaves a lumpy surface. In my case it didn't matter much since I'm looking to protect my tools more than anything, but if you are looking for that perfectly smooth surface under your tools, it most likely won't be.

I’ve never used this product before and after seeing videos of it on YouTube, I decided to order a sheet and try my hand at organizing my power tool drawer. Shipping took forever, but that’s not really anything to do with the product. I missed the weekend that I had planned the project for first go round. Once it arrived, I started to measure the panel for a tight fit in the drawer and found that the rectangle of foam was not square, no two sides rep parallel with one another. A short side was a quarter inch off and end the long side almost one half inch. I ended up having to cut from the center of the panel as it didn’t come with a straight side to measure of of. It’s just made for more work upfront. Once fit to the drawer, I started laying the tools out and cut them in one at a time I had no issues, achieving a tight fit and a clean bottom with basic hand tools, and a sanding desk on the Dremel to finish the bottoms, flat or contoured as needed.

This is perfect for custom toolbox/chest storage and organization. Can be cut with a box cutter/knife or laser cutter! Shipped well too.

Used to create cordless tool storage in Milwaukee Packout boxes. Purchased 2'X4' piece. Granted it takes time and patience cutting tool cutouts. Cut large pieces apart with fine tooth hacksaw blade and xacto knife for cutouts. Although layers don't separate evenly, found that making horizontal cut to start peeling helped. Sharp blade worked OK to smooth areas where peeling wasn't even. On a couple of heavier tools, fed Velcro straps through foam that help to hold tools in place if toolbox is carried on side. Created excellent protection and storage of these tools keeping them from damage by rattling around in tool box or bag. Since I already owned these cordless tools, didn't need to spend amount to purchase Packout boxes with tools included. Purchasing foam in bulk size saved about 50% from Milwaukee's cost for precut foam which would still need to be cut to fit tools. Well worth the time and patience to cut my own.

Great product. Im not sure why people complained about being difficult to pick and not square. My sheet was square so I only had to make 2 cuts for my single drawer. I also had no issues picking it at all. You just have to make a nice straight cut with a SHARP blade and then peel it up as one solid piece. Don't try and pull from the top. Get your finger under there and peel it up like you are peeling up a stuck piece of tape and keep doing that. It won't be 100% flat but who cares, it's to support tools and what not. You can get fancy with a hot knife, soldering iron or other tool. TIP: Take some painters tape and put that down first, then you can draw out your tools. 2nd Tip: Take the painters tape and it apply it to your jeans/shirt first a few times. I found the painters tape DID pull up some of the black material if pushed down too hard but it worked GREAT to lay out my tools.

Excellent foam for Leaning out anything at work or around the house. Definately another Superior FastCap product. There is one thing I would like to say that was a little misleading in the product description from the seller (not a FastCap error). the description advised that the foam was easy to pull apart. I purchased the thicker foam thinking if I needed a thinner one, I could just pull it apart and make it work. I was wrong and ended up ordering the thinner one later. When it says easy to pull apart, I believe they are meaning pull apart after cutting a piece out, say half way through. Trying to pull apart and entire piece to make it thinner didn't works as well. It was easy to pull apart, but wasn't exactly uniform (didn't pull apart evenly). Of course I could have trimmed it up with a blade if I had to, but it was just easier to order the thinner one and keep this one for the thicker jobs.

Good for shadow boxing your tool box. I mainly use it for packaging up items I make and cut a fitted slot out for a snug fit. Looks good and lets the buyer know you pay attention to detail and care that it gets to them safely. I like the dual color for added pop. Very strong foam and easy to cut and peel. With the multiple layers it’s easy to get your finger in there and pull out the exact depth you want.

Great product. As advertised.

My toolbox looks awesome, spent a couple hours cutting in the tool outlines, well worth the effort. Foam is layered in 1/8” layers, so easy to get a perfect fit.

good & solid

Perfect for lining a tool case with heavy tools. Used it to replace "pick and pluck foam", which was not up to the task.

Easy to cut and peel. Makes your custom tool organization easy.