Rislone's High Milage Compression Repair

I have a 1989 boat. The engine is the Mercruiser 4-cylinder Alpha One. The engines were actually made by General Motors. They were used in Chevys, and they adapted them for marine use by putting their own intake manifolds and exhaust manifolds on them. I would note that marine engines have a hard life. They are frequently run wide open at 4,000 RPMs for long periods of time, causing more wear than the same engine in a car would experience. So, my engine was 34 years old and very tired. Starting was unreliable. It would crank and crank until it would catch, and then I had to keep the rpms at about 3,000 for a while or it would die. You could tell one cylinder was not firing- maybe two because of the lumpy running and engine shaking. Idling was out of the question for at least 5 minutes. If other people were at the boat ramp I felt embarrassed because of all the blue smoke my boat made. I decided to add one container of this product to my oil to see what would happen. The first four times I started the engine, there was no change. About the fifth time, I noticed it was running more smoothly. Then, after about a month, I accidentally started the engine without giving it any throttle- I just turned the key. It started right away (miracle #1) AND idled smoothly at 700RPM (miracle #2). I could not believe it! I turned it off and started it again, and the same thing happened. Since then, it has done this every time. No blue smoke, no engine shaking, engine starts immediately and idles smoothly. That's my story. I don't know what they put into this product, but whatever it is it actually works. It restored my balky, high-mileage engine so it now starts and purrs like a baby. I would highly recommend this product, and that's an understatement.

I started noticing some rough idle and blowby so I change the plugs and wires and still had some issues. Took it to a shop and they did a compression test and found cylinder 5 was at half the pressure. They recommend an engine replacement. I searched and found this additive Rislone. I skeptically added just half the bottle at first. The engine sounded more silent and less rough than before. I then added the 2nd half now knowing it wouldn’t hurt the engine. So far I’ve driven about 500 miles. I noticed the car sounds and feels a lot better. I don’t have any blowby and gas mpg looks about right. It’s possible the solution freed up some gunk on the pistons rings or idk but I think it works. I would recommend you try it before condemning an engine and getting a new one. The solution is think like honey so it kinda worried me at first but it turned out fine. It probably cleaned up all the engine parts.

This did seem to quiet my engine down a little

sealed truck for about a 7month so i drained it then and added another bottle and it resealed so here i go again

Bought a can for my okd Subaru Forester when it developed compression issues. Although it didn't cure the issue, it did help noticeably. I couldn't have aAdked any more of it for the price.

Give this a try before replacing piston rings. I have an old and tired Tecumseh flathead that ran okay for its age but smoked a lot and blew oil out the breather tube. I used the Rislone as directed and it made a huge improvement. Don’t expect immediate results, as piston rings can take some time to come back around. Engine still smokes a bit under load, but consumes oil far less and runs well. I’ll have to do a rebuild eventually, but I rely on my machines and can’t afford that much down time. Highly recommend!

Works as advertised.

My crankcase had serious blowby. Oil coming out the dipstick and the ccv lines. The engine was knocking also. After 3 bottles of this stuff it's back to running normal.

Hasta proximo cambio de aceite no oo usaré, ya q eche sellador de junta de culata y no se pueden mezclar. Pero conociendo la marca seguro q va de maravilla.

It actually works so I'm well pleased

It’s amaizing. Just let the engine run for 5 minutes and the knock sound was gone

Good product

Pas d’ effet