Thermal Grizzly Minus Pad 8-120x20x0.5mm 2-Pack Thermal Interface Pad, Electrically Non-Conductive, High Thermal Conductivity & Compressibility for SSDs, GPUs & Electronics

Worked perfect and the thinness did the job great. Will buy if I ever need another one.

These thermal grizzly pads are awesome - high performers. They are more expensive for the size though so I bought this 120x20x1mm to apply to the high heat areas like the VRAM on the baseplate. I paired these grizzlys with a cheaper 1mm alternative with a lot more surface area to work with for the less sensitive areas and the backplate (the blue stuff in the image). The combo worked like a dream. These pads don't deform or elongate at all when removing the film, unlike the other brand I was using (AIYANNI). This made it really easy to apply and stay in place (and cut to precise rectangular areas) and just sticky enough! As far as the orientation, I would recommend FLAT side down on components and rough side upward because this will make it easier to remove baseplate in the future without tearing off pads since they will have a better adhesion to the PCB components. When it was all said and done, my card was 20 degrees C cooler!! This was at both resting and full-load. If anybody was worried about the different size of pads on this specific card, fret no more! 1mm is perfect for all areas! Just be sure to carefully cut and apply to the correct areas and components, and you're set!

Been using my 1TB WD SATA M.2 in my enclosure and the thermal pads that came with it were garbage honestly probably 0.5mm. Bought this to bring down temps. The good thing about my case was that I was able to apply some thermal pad the the top and bottom of the SSD with no problem and actually helped me screw the SSD down a lot fast so can’t complain. Excellent pricing for this SSD and the thickness is excellent for small enclosures or motherboard m.2 SSDs. With the amount they give you I was also able to apply some of the thermal pad to the enclosure controller and it fit in the enclosure with no gaps in the pad. Fixed the heating problems I was having. And was pretty durable when I had to reapply it compared to other thermal pad brands. The SSD is running at 35 degrees C while copying over 400GB of DATA to my NAS drive and my external drive.

Effective easy the best for my high end laptop dell 7770 with rtx and i9 and yeah does not overheat now

Replaced my old pads with this. It worked perfectly on my Dell Alienware 17 R4. Only replaced 1mm ones.

Its easy to use, it is delicate. But seems to work

Came in quick, great packing, used for PS4 pro. System has never been so quiet! 5 out 5! Worth the price!

Did the job so well for my ps4 slim

The Thermal Grizzly Pad was quite an interesting item to use for cooling down heat intensive devices such as the Playstation 4. It does look like a long stick of gum or a Laffy Taffy after opening up the sealed package. Both flat sides of the pad were stick onto a thin plastic cover for protection of dirt and debris. The plastic cover can be quite tough to mark any measurements without using a fine marker or a wet pen. Using a fine sharp tool, it can be cut into near to exact measured pieces for your project. In this project of mine for instance, I used it to help cool down my original PS4, replacing the stock thermal pads. After testing my PS4 out for few hours with the new pads, I've noticed quite a difference in cooling that help lessen the use of the stock fan, so it doesn't sound too much like a jet engine. I would use this product again to replace other heat intensive devices in the near future.

Se pega y funciona bien.

Bought from Scorpzon trading, received freshly imported, totally geniune product, when I checked the label, found that the seller Scorpzon is the official importer for thermal grizzly products in India, came in a resealable pouch, used it for my MSI gaming Laptop to replace the factory installed thermal pads. Works as advertised, easy to stick, don't forget to remove the protective film from both side of pad before installing.

Usé este thermalpad para las VRM de mi GTX 1080 8X de MSI. Había cumplido la garantía y nunca se le había realizado un mantenimiento y las temperaturas estaban ya rondando los 78ºC mientras jugaba, hacia stream y mantenía 2 monitores. Cuando abrí la gráfica a parte de sacar pelusa como para rellenar un sofá, vi que el thermalpad que venia de fabrica estaba ya negro completamente y de una textura un poco viscosa. Cuando lo cambié aproveché para cambiarle la pasta térmica ya que que la de fabrica estaba seca como solidificada y puse la pasta Arctic MX-4. Cuando inicié el ordenador la gráfica en modo reposo (2 monitores, viendo Youtube (sucedaneo) y charlando por Discord marcaba un rango de entre 33ºc - 37ºc. Pasando test de stress GPU de FurMarks no sobrepasa de los 67ºC. Un acierto de 10, de ahí mis 5 estrellas. Es fácil de manipular, cortar o instalar.

This a great product to mantain low temperatures of electronic components around CPU and GPU. It's a bit expensive but quality is good. Easy to apply due to its due to small size and good quality paste. The Functionality and performance increases when used in combination with Kryonaut. Temperature around GPU and CPU were around 80-90 Deg celcius. After application the Temp of device hovers between 40-50 at room temperature.