Ruger LCR Front Sight

5 stars for loving this on my gun. BUT this thing is VERY DIFFICULT to get on your gun. If I was to do it over again, I'd take it to a gun shop and pay them to put it on. Getting the old roll pin out was not difficult. I used a 1/16" punch. You will need to use a lot of padding and put the gun in a vice. Putting in the new roll pin was very tedious and NOT fun. I used the 1/16" punch, a small hobby hammer and a variety of other tools and objects to get the new one in. Even then, the end of the roll pin ended up frayed slightly and a little (not a lot) deformed. Ugh. Just using the 1/16" punch to hammer it in did not work. The punch damages the pin and slips off too easily. To get the last third of it in, I had to use pliers and squeeze it in trying not to hurt the gun. The pin went in but the very edges of it ended up slightly frayed and flush against the new sight. Not bad, no one will notice, it's in 99% of the way and will not budge, but it bothers me. The pin really should be slightly smaller and a better fit. Took me around an hour. Awesome sight though. It works great and I would recommend it. Maybe just hire someone to put it in.

This sight is advertised as "does not fit the LCR 22 or 22 Mag." That's not technically true. The sight easily installed on my LCR 22 WRM in less than 10 minutes. With a proper 1/16" roll pin punch and some kind of block (a roll of duct tape works), you can install this sight in no time. I think the people complaining about the install don't bother to use a roll pin punch. To the sight itself, the Hi Viz sight measures .244" tall versus the OEM sight at .218" tall. On the 22WRM, that moves the POI down significantly (8-10" at 10 yards) with a normal POA. Your choices are really 1) re-install the OEM sight; 2) find another front sight option; or 3) "AIM HIGH" as they say in the Air Force. If you place the entire green dot "above" the rear sight, i.e. higher than a normal sight alignment would dictate, you can move the POI back up. I think I'll probably look for some other front sight option. I have to give the sight 5 stars because it installs easily, shows up clearly and crisply, and they DID say it wasn't for use with the 22WRM. Can't ding the sight because of my off-label use.

I have two of these sights. They are very nice even in low light conditions. Any darker and you would want a laser sight. The only complaint I have is that there is no hardware with it like the XS Sight. Though if you have a small punch and some super glue, than this is great deal for you. The first one took a good 20-25 min. because it was a pain to line up the pin, but the second one took only minutes. ***** ADVICE--- Use a rubberband to hold the sight on and in place when you are hammering the pin. This will help greatly. I also advise not throwing anything away until it is assembled because those pins have a mind of their own sometimes.

Why did you pick this product vs others?: Easy to install, makes aiming much easier.

Works great in low light, but it is not for no light. Have a trained professional install it or you risk scratching your barrel.

Really bright nice sight worth the effort to ge on. Old pin came out easily with 1/16 punch as recommended. Old sight came right off new one right on so far so easy. Putting in the pin was a different story I ended up using the old pin and a little was sticking out after a great deal of effort setting it with a punch so I carefully ground it flush with a Dremel tool. Start the pin with the sight off the gun that works but setting it in was impossible. If I had to do it again I would grind the pin down a bit with a file or wheel. The final result looks great but I would never done this on one of my smith and wesson revolvers.

If you have owned one of these, you know. They are very high visibility and a great upgrade to a painted front sight.

Excellent quality, works as it should, easy to install myself and did not change point of aim .