MICTUNING MIC-LSB1 Laser LED Light Bar Rocker Switch ON-Off LED Light 20A 12V, 5pin, Blue

Bought this to install a LED bar on my garden tractor, yes I said garden tractor! I do a lot of plowing in the neighborhood with my tractor and needed this for the late nights or early mornings when I am making a ruckus and waking up neighbors...all to their benefit of course.Anyways, this arrived super fast (thanks Prime), and came with decent enough directions. I do wish it came with a cut out template, that would have made me love it more! A simple piece of paper that I don't have to guess and check to create would be awesome. BUT, it didn't, so I made one out of the cardboard packaging, positioned it where I wanted it on my dash and penciled the cut out. Took the time cut out the dash and make sure it was level and centered for the install. Go in small bits, better to have to shave off then have an oversized hole!The connections were super easy, the directions were great at detailing what to do on the switch end...not so much the battery hook up end so beware you should have a plan before diving into it. After hooking it up to the battery and throwing in my own inline fuse to the LED bar I powered it up and it simply worked. I love the blue light when it is on, especially because I have it hooked up to the battery and not to the on/off key.In short:The good: simple hook up, works, looks great, good directions on the switch end, you can get this switch in many flavors!The bad: none really, would have liked to see it come with a cut out template

Works well

I used this switch when I installed a light bar on my Polaris Ranger 900 XP. I worked perfectly for me in this application. The switch fit perfectly in the existing blank in the dash. The switch feels nice and solid and has a positive lock when going back an forth. There are two nice touches that MICTUNING provides with this switch. It comes with a diagram that clearly labels the connectors on the back side of the switch. I used this switch to replace the round rocker switch that was included with the wiring harness I purchased for the light bar. This diagram made this change as simple as possible. MICTUNING also includes two sets of jumpers for the hot and grounds for the lights on the switch. It took me longer to pull the blank plug out of the dash than it did to wire this switch up and get it in place. I will use these switches for any other projects I have.

The media could not be loaded. Great switch, the included wires are only 18 awg, I am running a relay so it's just fine, my other switches had 14 awg (different vendor).

Nice switch. Easy to install in rocker-switch blank on the dash panel of our 1998 Jeep TJ. Nice blue color when on (we purposefully switched the hot & ground leads so that the backlight stays dark when off... which I prefer).This one now controls the light bar mounted to the front of our Jeep. That bar came with a wiring harness that had different connector ends, so we needed to use the jumper wires that came with this switch. easy to figure out, though the leads did pull out of the adapter ends way too easily. We reset them all using needle-nose pliers and did not have any further problems after that.Instruction sheet is just about worthless but we figured it out through trial & error (thankfully, no errors).Plan to purchase one additional rocker switch from this company... for a set of fog lights... already purchased and installed a switch for the lighted whip installed on the rear bumper.Recommended.Go for it.

Look nice in the rzr

This is the second of these MICTUNING switches I have purchased and will buy more as the need arises. This one had much better directions and a wiring diagram included that made install a breeze. The switch has a back light that lights up with the ignition on and the blue color matches the stock Polaris rzr4 1k XP back light color perfectly. One would think they were stock if you didn't know. The size is about 1/16" larger in width and height than the perforated cut outs on the rzr dash but I would rather have to carefully file extra out of the dash hole until it fits than have the hole too big by following the perforations.

I really liked the way the switch was made and the sturdiness of it. The reason I downgraded it on installation was that it did not fit into my original switch cut outs. They were just a little small.