AOLISHENG 1 Pair Undermount Soft Close Drawer Slides 9 12 15 18 21 24 Inch 80 lb Load Capacity Full Extension Ball Bearing Hidden Bottom Mount Rails Locking Devices Concealed Runners

Quality product. Excellent performance. Instructions could be expanded to better assist first-time DYI installer/end-user.

The media could not be loaded.  I tried many soft close doors and I had the hardest time finding ones that were easy to install and would go in level. These made it easy to do that! They work well and are very sturdy. The one issue I have is the height of the slide itself. It takes up about an inch of space under the drawer. I wish they were just a bit shorter. I had to make my drawer fronts bigger to cover the gap.

There are only limited instructions available for the installation of the Aolisheng undermount soft close drawer slides. Almost all of the necessary measurements are in metric exclusively. Use the following measurements at your own risk. What I found is: The rail setback is 4mm or 5/32". Drawer width is the opening less 42mm or 1 5/8". Maximum drawer height is the opening less 26.5mm or 1 1/16".Look for a video titled "How to install AOLSHENG bottom hidden drawer slides." The video provides the necessary drawer sizing and installation specifications, but not much else.Shop these drawer slides. Pricing varies widely with time and across many markets. There appears to be no MSRP.I have not installed these slides yet, but in my hand they look to be well constructed. Weight limit is 35kg or 77 lbs according to the paperwork provided with my slides.Knowing the specific measurement for setback and drawer sizing, the Aolisheng undermount soft close drawer slides are no less difficult to install than any other. I am not sure if the jigs you can buy at Rockler will work with this Aohlisheng slide. If you know whether the jigs work, please comment.

Like the caption says great product he’s doing install

I'm a DYI homeowner and I wanted to install undercount slides for some new kitchen drawers that I made. These Aolisheng slides looked typical compared to the other brands, but there were a couple of problems: The installation directions were minimal and the "measurements" provided weren't exact. I built drawers with exactly 1/2 in sides which were supposed to fit into the slides, but they did not. In order to make them work, I ultimately had to use a planer to shave off 1/4 in on each drawer side. Also, the back/end angle attachments wouldn't allow me to screw the slides flush to the cabinet side-wall, so I wound up not using them. Finally, there seems to be a "catch" when first pulling out the slide that is annoying. This happens whether the drawer is attached or not. Once out, it works fine and is very smooth. I think I will try a different brand of this type of undercount slide there next time to see if that works better and is easier to install.

The media could not be loaded.  I did a video explaining what parts go where. Not a detailed installation, assumes one can install slides, this was mostly to overview the slides parts and locations.Of note, the slide length needs to be about 1/2 longer than the drawer to easily install the clips per their one image of installation.Basically, the slides are put in place/level. The black/red clips attach to the drawer, or shelf in my case, and slide over the slide/rail to be anchored in the back. I put in place, tapped, then drilled a small hole for the tabs to engage into....your call.Other than figuring out how it was installed, the only difficult part is how to attach the black/red parts in the correct place.....my way was a little awkward, but it worked. With drawer in place (pulled out, even in back, pulled red latch and placed black part into slide, released red clip, and then used a pencil to mark holes for screws.) Took a few tries without moving the drawer position, but it worked......those one image of this is that the clips butt to the drawer front.....which would work.

Extends 18" from the back of the drawer mounts front of the drawer fully Extended. Which means the drawer that has a depths of 18" only opens like 6" from the front of the cabinets. So you have like 12" of your drawer still remaining in the cabinetry. Makes it real hard the get stuff out of. I returned. The description is worded in such a way to make you believe your buying a drawer hanger that extends 18" from the front of the cabinetry. Maybe this is common knowledge to cabinet installers. But not to us folk just trying to ad a drawer or in my case an extendable shelf to put my dinner plate on at my end table. 6" is not enough room for a small bowl of ice cream let alone a dinner plate.

These worked out perfect for what I needed. Heavy duty, easy to install. It’s a bit tricky to determine the size or length for the drawers but worked perfect for me

La usé para un teclado musical con deslizamiento bajo el escritorio, sin problemas por el peso, desliza suave y no se suelta por accidente, justo lo que necesitaba. La adaptación al escritorio fue muy fácil.