Genuine Tumble Dryer Heating Element

My wife killed dryer and start looking for new one. I decided to look into it and try to sort without losing money and all that pain with new dryer. When trying to switch on dryer my fuse blows instantly and that was easy to google what it’s wrong with it. After watching vid on yt it was clear what I need to do to it’s check if element it’s toasted if not that something more serious. Take few minutes to unscrew back panel where element it’s located and after trying press reset button on it was clear what’s not working (reset button should jump back) After wrote down numbers from heating element I did research for new part, now before I go what happen I should say my original was 700w/1600w but Beko replaced that version with 900w/1600w and stop making original one. I find cheaper one on amazon and after buy 1 from seller (who send from amazon) I end returning as was wrong one... 2nd one I buy from spare2go (Seller on amazon) and was correct one still toke a week to sorted out because of wrong one. Save yourself problem and buy from them. After part come toke me less then 10 min to replace it. Back panel have a multiple screws and there 3 different sizes Top cover only 3 screws Heating element 3 screws To unplug element first need to take off 1 screw of connector then cut cable tie from back of machine connector it’s inside, both screw and tie located close to each other and need take a look from top to see, after that it’s easy to unplug otherwise will be hard to do it as it’s in small space. After that wire need go thru small hole with rubber ring one after another as both will not fit. And all done ✅ Saved £££ and wife happy as dryer back to work. Forgot to mention on Beko site that part cost around £50 then it’s cheaper here.

Great part which was easy to install. I had to buy the whole Heater Element even though the only part that had failed on the element was the NTC Thermistor, but price for an NTC Thermistor was £35 on its own. I have now sourced and obtained NTC Thermistors from China and can repair the failed Thermistor unit on your failed heater unit. My failed thermistor measured 364 Ohms, where the new Thermistor measures about 18000 Ohms, so the failed unit was telling the main control card that no heat was required so the Relays for heating were not being energised, so no heating in the Tumble Dryer, Most failed heaters are just the Thermistor failed, very quick and easy to replace,

My dryer had stopped heating. Had the usual noises but clothes would still be wet and cold. For around £30 I thought I'd give this a go. Easy to fit if you can use a screwdriver and follow a you tube video. Dryer is like new heating better than before and also has reduced cycle times as old one was slowly dying. Looks like they burn out after 2-3 years of regular use. Saved me about £250 and hassle of having a new one and old one taken away. No wiring required as all plug and play. Very easy. Beko usually only have 3 problems. 1. Make sure lint filter and sensor are clean. (Clean after every cycle) 2. Make sure condenser is clean. (Clens after 30 Cycles) 3. Heater could have tripped or burnt out. (Push reset switch on back of heater) Having checked and cleaned the filter and condenser I had no other option. Opened the back and checked the trip switch but not tripped. So changed the heater and works great. Comes with the two thermostats installed with new trip switch. Try this before throwing out the old dryer. Save yourself some money.

Item was as described and a straight swap for my broken one

Good product

My Beko DCU7230 Tumble Dryer was turning on and spinning but there was no hot air to dry. After some research on the Internet, it suggested that it was the heater element at fault. Found a video of how to replace the part by typing in to Google "DCU7230 heater element video". Ordered the part and received within a couple of days Took about 30 minutes to fit using a couple of screwdrivers. A few sharp edges during the process of replacing the element so take care. Some screws are different sizes so worth marking where the longer screws go. Otherwise very easy to do. Gave the inside of the tumble dryer a little hoover during the process. Do ensure you put the Tumble Dryer back together properly to ensure no dust or fluff gets into places that it shouldn't. Working like new again. Saved on professional call outs and a new dryer

This made my dryer work again. Pretty easy to fit (but loads of screws). A post mortem on the old one turned up that it wasn't actually the element that was bust, but one of the safety cutouts, but they are integral to this unit, so replacing the whole thing fixed it.

BEWARE I installed this onto my beko DCUR801W and works however it doesn't work well enough. Due to this being a different watt. New part is 1600w+900w however the old part is 1600w+700w didnt think much of this however it doesn't seem to be getting hot enough (which on the beko website is a sign the element is wearing out and will require replacement). This element will dry the clothes only to a damp state and not actually dry them. The listing states its for this model but when looking on the beko website its not got a model number just beko models. Also the top is different see pictures so buyer beware!!

Die Ware ist wie erwartet angekommen.

Au top pièce identique à l’original parfait

Parfait, adapté à mon sèche linge essentiel B C'est reparti pour un tour

Perfecto, quitar una y poner la otra.

Sehr zufrieden