Force®8 Half-Mask with PressToCheck™ Replaceable P3 Filters, Suitable for Dust, DIY, Painting, Sanding, Plastering, Water based spray paint, Gardening, Glyphosate weed killer (BHT0A3-0L5-N00)

Why did you choose this product over others?: Comfortable, reliable, and easy to use I started using the JSP Force 8 half‑mask respirator at my salon while working with strong adhesive for eyelash extensions and fine dust during nail polish removal .The Press‑To‑Check P3 filters give instant peace of mind,I just press the filter and feel the seal, so I know it’s working every time. The Typhoon exhalation valve is a game-changer,breathing feels natural, and there’s minimal moisture build-up even after hours. The soft rubber and 4‑point harness make it snug and comfortable, with no squeezing on the nose bridge. I can easily clean it after treatments, replace filters monthly, and it still feels fresh. After using pricier disposable masks, this reusable option is far more cost-effective. I only wish I’d switched sooner!

I have just bought my second one of these after eventually breaking the first one after extensive daily use at university. This was entirely my fault as I was hoovering to clean the inside and accidentally sucked out the rubber membrane between the mask and the filters. I use these masks to protect me from fine glass and silicone dust which are extremely hazardous when making moulds and coldworking glass. Not only are these masks very comfortable due to the rubber nose and mouth seal, but they are very easy the adjust, and don't place too much pull on the face, or pressure on the sinuses when compared to disposable masks. They are also far better value because of them being reusable. As mentioned earlier the outside of the mask can get dirty and so can the inside which is why it helps to keep it in the supplied plastic drawstring bag, although it can be a little awkward to clean the outside where the straps attach. The strap system on the neck makes it very easy to remove and reapply the mask whilst keeping it round your neck by just pulling it over your face. It does feel a little weird at first when wearing it with the strap being across your neck but it works well. The plastic ring head piece is easily adjustable and sits on the crown of your head comfortably. I wear this for long periods of time (at 3-8 hours in one sitting) and it's much more comfortable than disposable masks and just lately I have found most places have been out of stock of the P3 disposable masks. Unlike the aforementioned masks the elastic on this reviewed mask doesn't come off or snap as it's well secured and not stapled. It's extremely easy to tell if this mask is fitted safely by pressing in the 2 filters either side and breathing in to check that the mask is airtight (you shouldn't be able to breath when these are pressed in). Sometimes I end up with slight marks on my face where I have tightened the mask too much - although this is normally when wearing several other things like a cap to protect my head and goggles. As with many masks, it can be a slight pain to wear other branded goggles with masks such as these due to the top of the nose piece. As such I have replaced my bolle goggles with JSP EVO® Goggles (same brand as the mask). These goggles are very good, with a bigger screen than my bolle ones and fit better with this mask. I still find I have to have the elastic headband at a diagonal angle higher up my head to keep them tighter to avoid a gap and fit close to the upper rubber nose part of this mask. I was so impressed with the ease and comfort and price of this mask from 3 years at university that I made the decision to get another of these rather than risk using often more expensive and poorly rated all-in-one goggles and masks which have a tendency to steam up more. I have been wearing this mask and goggles combination recently on a daily basis whilst doing DIY for approximately 8 hours on and off (creating a lot of dust from sanding filler, and lime mortar in a very dirty and dusty 100 year old building). Unlike my previous use at university I have admittedly had problems with excessively sweating whilst wearing this in the extremely hot and muggy heat this summer which has led to having a small swimming pool of sweat build up in the inside of the rubber part of this mask - I don't put this down to the mask but rather to the conditions I'm working in. When this happens I just dry the excess with a bit of paper towel and leave it to air dry and it's good to use again. I don't believe this is a fault of the mask and it doesn't help with the goggles steaming up so much. I did struggle to get the filters to fit because the circular seals are tight tough plastic and the rubber nose part is soft and flexible so it's hard to rotate them and click them into place. They were not just tough to fit but the arrow system was slightly confusing as other people have stated in reviews. You just need to keep twisting them round and they do apply the correct way as pictured on the instructions and photos on here with the white filters sweeping back and diagonally upwards. Personally I think if you buy this, the fact that these are the filters supplied, I think there is no reason why the manufacturers cannot supply them already fitted (clicked in place) to avoid this problem / confusion. I highly recommend the mask - I know I can trust it to protect me from hazardous dust and it's largely comfortable!

As someone who values both safety and comfort in the workplace, I recently purchased this mask, and I must say, it has completely exceeded my expectations. First and foremost, let's talk about safety. The JSP Force 8 is engineered to provide superior protection against a wide range of airborne hazards, including dust, particles, and various contaminants. Its innovative design features two high-efficiency particulate air filters that captures even the smallest particles, ensuring clean and breathable air for the wearer. But what truly sets the JSP Force 8 apart from other respirator masks is its exceptional comfort. Constructed with soft and flexible materials, it molds effortlessly to the contours of the face, providing a snug and comfortable fit that lasts throughout the workday. The adjustable straps and padded nose bridge further enhance comfort and ensure a secure seal, eliminating any gaps or leaks that could compromise safety. Another standout feature of the JSP Force 8 is its versatility. Whether I'm working in construction, woodworking, or any other industry that exposes me to airborne hazards, this respirator mask offers reliable protection without hindering my ability to work efficiently. Its low-profile design allows for unrestricted movement and visibility, making it suitable for a wide range of tasks and environments. Durability is also worth mentioning. The JSP Force 8 is built to last, with rugged construction and quality materials that withstand the rigors of daily use. Unlike disposable masks that need frequent replacement, this respirator mask is designed for long-term wear, providing both cost savings and peace of mind. Maintenance is a breeze with the JSP Force 8. The reusable design allows for easy cleaning and disinfection, ensuring optimal performance and hygiene with minimal effort. Plus, the replaceable filters make it easy to keep the mask in top condition without the need for frequent replacements. In conclusion, I highly recommend the JSP Force 8 respirator mask to anyone in need of reliable respiratory protection in the workplace. With its unbeatable combination of safety, comfort, versatility, durability, and ease of maintenance, it's a must-have accessory for anyone working in environments where airborne hazards are a concern. Protect yourself with confidence and comfort with the JSP Force 8 respirator mask.

I purchased this for some spray - painting projects in a confined space. The mask itself is excellent; fits well and is comfortable even after extended use. The press-to-check filters are handy to make sure you are fully protected and the mask seals properly. The included filters work well for dust (such as sanding rust, old paint etc.) but are not effective against aerosols which it did state they were. Something to be aware of. JSP do sell uprated filters which are twice the size and do properly protect against spray paints/lacquers etc. If you plan on doing such work I'd recommend buying those too. Overall I would definitely recommend this mask especially given the price point.