Edge Supply Walnut 24 x 96-inch Flat Cut, 3M Peel and Stick Wood Veneer Sheet – Self-Adhesive Wood Veneer, A Grade, Smooth-Finished – Versatile for Furniture Restoration, Cabinetry & DIY Use

Beautiful material, thick with the backing and easy to work with, with the 3M Peel & Stick. I was creating Shaker-Style End Panels for my cabinets - Real White Oak Rails & Stiles and the veneer over 1/4 birch plywood for the center panels. A couple of installation notes that are important. First, I gave the Plywood two coats of Water-Based Polycrylic with a light 240 grit sanding. This will give much better adherence to the Veneer 3M coating by sealing the Ply to a smooth surface. Then, it's best to be in a warm environment. A bit cool in my basement workshop, so I applied upstairs in a heated room at about 70F Next, when you apply it is critical that you apply pressure across the Veneer - it's important to know that the adhesive is PRESSURE activated. But additionally, you need to ensure all the bubbles are worked out before it sets up. I used a combination of a carpet-tucking tool and a J-Roller. Roll/Push from center out initially in both planes. I found I could hear a 'Rice Krispies' type of popping as I pushed small bubbles (these were not visible, the only indication was the audible response as you 'pressed' them.) Once confident it was pretty well , at least initially, secured, I flipped and trimmed it. Blade with the grain and, although you can cross cut with multiple blade strokes, a veneer saw gives much cleaner cut in that plane. An alternative to a specific Veneer saw could be a Japanese Pull Saw, blade with a finer, higher tooth count. Then flipped back over and worked the veneer surface some more with heavy pressure from the J-Roller, especially towards the edges. The now combined panels will be cut to final size on the table saw and given a final finish or Rubio Monocoat. Some reviews stated they had bubbles - in my opinion the Bubbles are due to inadequate preparation and application technique. This adhesive is fabulous but can only work as well as it will be applied.

This is one of my best buys from Amazon! Absolutely beautiful Mahogany veneer that is extremly easy to use and stain. I needed to replaced the veneer fronts of two antique dresser drawers. The cost of having an antique repair shop do them was prohibitive, so after watching a few You Tube videos, I decided to see if I could do them myself and ordered the veneer from Amazon. I was thrilled to open the box and see the quality... the wood grain of the mahogany veneer is beautiful and it was very easy to apply. I do suggest watching a You Tube video, it helped. The drawers came out better than I could have imagined and they look exactly like (if not better than) the original veneer on the remaining two drawer fronts. Very easy to sand and stain.

The item description is wrong, this is not peel-and-stick. It is PSA, pressure-sensitive adhesive. It is slightly tacky and easy to work with, then apply pressure to set the adhesive. So far, no failures. Vaneer grain quality was excellent and similar to the picture. Very pretty product and very easy to use. Shame about the poor item description.

Peel and stick sheeting is so easy to work with, cuts with a good pair of scissors or razor knife to work in most any project. The peel and stick adheres very well and turned my old banged up cabinets into a great new look! My only complaint/warning that knocked it down a star is that it did not take to polyurethane the same way other veneer sheets or lumber of the same species... (different manufacturers') possibly because of the pre-applied peel and stick trapping air? but a little pre-staining made the difference, just not something I needed to do on other products. staining is a caution helpful tip

Just a few days after applied, it started exhibiting air pockets. I ended up removing it; a waste of time and money.

We got this to patch a couple areas on our boat that were severely water damaged. It matched the existing veneer and went on flawlessly. The repair looks great and very professional despite our being veneer noobs. We're now looking for other places to fix. One word of caution, the adhesive backing is brutally effective. Be very careful in your positioning as once you press this stuff into position it's there to stay. All-in, it's fun to use and gives a beautiful result.

Pros- good wood quality. Prepped project substrate with three coats sanded polyurethane that provided smooth surface for excellent adhesion of 3M PSA. Veneer cut easily with box cutter/heavy scissors leaving very clean edge. Veneer flexed nicely in vacuum press to adhere to waterfall edge and curves. Cons- eighth of an inch gap between edge of veneer and adhesive in some spots. Probably would have been okay without, but added bead of glue anyhow. CAUTION- you basically get one shot at getting placement right once you remove the PSA backing. The PSA adheres instantly so ensure you’ve got your veneer cut and placement right BEFORE you peel. Excellent product that I’ve already purchased again for next restoration. It’s a little pricey, but I didn’t want to mess with glue required for less expensive non-PSA veneers- anything to reduce the number of variables for my first veneer project. Very pleased.

I have a 96" by 24" desk and thought this sheet would cover the whole thing but the veneer I got is actually 94.5" by 23" and wasn't square to boot. In addition, the adhesive doesn't go all the way to the edge which means you lose another half inch on the sides. It's a fine veneer and looks great otherwise but now I have gaps around my desk and will need to figure out another way to cover them. Be careful if you're getting this for an 8'x2' piece of wood because it won't fit. It's fine otherwise.

Se travaillle tres bien

I was very disappointed when I opened the package up. The 3 strips that made up the full width of the roll were dramatically different in colour, with the centre strip being much lighter than the two outside strips. I had 3 sides of a floating mantle to veneer, and ended up wasting a lot of an overpriced roll to scrape together a finished product. If the timeline hadn’t been so tight to meet the clients deadline, I definitely would have returned. Another issue was a series of bark inclusions on one end of the roll. The quality was on par with something from a box box building store, but definitely not up to a standard for something priced over $120 CAD.