Alinsea Screen Protector for OnePlus 7 Pro/7T Pro Tempered Glass [Full Adhesive] [Fingerprint Sensor Compatible][3D Glass] Screen Protector for OnePlus 7 Pro/7T Pro

Excellent product with clear instructions and all required accessories, making it very simple to install. Was able to fit it quickly and with no bubbles. Definitely recommend.

Overall the cutout of the protector fits nicely. Be careful not to let the LOCA adhesive spill off the screen during applying, i was not careful enough and resulted in 2 bubbles on the screen. Still giving 5 stars due to it being my carelessness. Overall highly reccomended to buy!

I've been trying this screen protector since last week and for the moment has done a perfect job! Good quality overall, the installation isn't to difficult and following instructions step by step is easy to get a nice result. Finally a glass protector that doesn't stick only on the edges, really good touch feedback and no issue at all with the fingerprint sensor, which works perfectly . Definitely recommended!

Aufkleben war durchaus anspruchsvoll, aber durch das YouTube gut zu befolgen. Hat mein Handy gerade vor dem über zwei Meter Sturz auf Badezimmerfliesen gerettet. Displayschutz ist hin, aber Handy hat keinen kratzer abbekmen. Würde sofort wieder bestellen, aber da die Lieferzeit 3 Monate beträgt muss ich leider nach etwas neuem schauen. Fingerabdrucksensor funktioniert tadellos

Alright, I've been trying so many screen protectors for my OnePlus 7 Pro and I guess due to the curved screen, it's hard for manufacturers to get it right or another. I tried three other glass protectors, but they all turned out to have the glue only around the outer edge and it was a black glue strip. So not only did the protector start sliding around after a while, you have a black line around your screen, partially blocking. Plus, no glue on the screen, means you have to press the protector to the actual screen and THEN it registers your finger and they have the grid marks on them for the fingers to work. I then tried the plastic film ones and while they did work better, you get the indentations, the scuff marks and you lose some quality on the screen. Somewhat like an OLED to the old CRT screens, details are lost with them. I had looked over these UV curing kits before and wasn't too thrilled about pouring glue over my phone, having it run off the edges and using a UV light at the same time. But after five failed previous products, I decided to try this one, especially when it was just $10, compared to the others that were as high as $50 for a kit! The description doesn't state it, but this kit comes with just about everything that you need. A pair of new, clean plastic gloves; two sealed lens cleaning kits (each kit has a medium sized microfiber cloth, screen dust stickers and alcohol wipes); the tube of glue; the UV light stick (you need your own USB-C cable and wall adapter); the small assortment of rubber barriers; and instructions. I placed the rubber foam barriers as I saw fit, according to my phone. I used them all up, covering the top speaker right at its very line, the bottom over the speakers and ports, the power button and notification slider, and the volume buttons. I modified as I saw fit and made sure they were completely pressed and blocking off any flow to them of the glue. Meticulously cleaned the screen, then poured the liquid glue as directed, over the center of the screen without squeezing the bottle, while I had the phone sideways in front of me (landscape mode). FYI, I had my phone off during all of this, so it wouldn't register or keep turning on or other during the install. Then placed the screen protector from the side and placed it over the glue. The glue starts moving across the screen and I picked up the phone and titled it as needed, to ensure it reached the entire screen. After making sure it covered the whole screen, I made sure the protector was centered over the screen and fine (I had a bright work light, which GREATLY helps, as the light actually showed where the display screen is and where what little bezel starts at). Once that was done, I used the UV light and started curing the screen for about 90secs, including the edges. I then stopped and cleaned the phone's sides and bottom with an alcohol wipe, while it was still wet. This glue has a smell to it, FYI, so be ready, but I made sure no glue was on the sides or corners or back. Once that was cleaned up (maybe a few mins) and no glue anywhere BUT under the screen, I used the UV light again, moving it slowly across the screen and directing it at the sides as well. It says to spend about 3-5mins curing it, I believe I spent about 10mins, maybe more (oh okay, probably about 20mins) curing it. The UV shuts off after 5mins and you just unplug and plug it back in. It turned off about 3-4 times with me, so yeah, I spent extra time curing it all. I think my phone has a tan line now... I wanted to be absolutely sure it was cured and ready. From start to finish, including unpacking the box, prepping the phone, installing and curing it completely with my curing time (~20mins), it took me 45mins to install this protector. Now, I took my slow slow time, double checked everything, made sure it was correct and did with what my spouse would say is a serial killer's zeal during the install, but it came out unbelievably perfect. It nearly brought a tear to my eye, seeing how it came out, especially after all the previous, failed products. It absolutely looks like there is no protector installed whatsoever. And it feels oh so so very smooth and with finger gliding giddiness, when you're using it. My spouse said she couldn't even tell anything was installed. There's absolutely no bubbles, no marks, no scuffs, no dirt, no dust, NOTHING. I do believe I have never had this measure of success, ever, installing a screen protector before and I have installed probably nearly 100? This is my 8th smartphone, my spouse's 9th, plus all my family members' phones that I've install them one, including glass and film, always something underneath them, always breaking, wearing, scratching, etc. This is just plain superb, honestly. I also have it installed with my Poetic Rugged OnePlus 7 Pro case with no issues, but I have removed the installed screen protector from the Poetic case and cleaned the glue on the inside of the case. The case rides/sits on the protector itself and doesn't pick or lift the screen protector whatsoever. Some of the other glass protectors I had, the case was picking or sliding it sometimes. With the Alinsea one, the Poetic seems like a destined marriage with it, it's great. So, all in all, a little tedious install process, especially if it's your first time with such a UV kit, but in my opinion, it was well worth it. Also, I have dropped my phone about 3x since it's been installed and it hasn't cracked or chipped, still perfect. Of course, with the Poetic Rugged case and this screen protector, my OnePlus 7 Pro is built like a tank now, so I'm not surprised it's still fine. I mean, it better be! I just spent all this time installing it all!