onlyfire 14431 Universal Spark Generator Replacement for Gas Grill Models by Broil-Mate and Others, 2 Male Outlet AA Battery Push Button Igniter

Needed a replacement ignitor for a ProComm / Feature Comforts propane ventless heater model MD300TBE (in owners manual also listed for MD100TBE and MD200TBE). Original ignitor part model number is DHLG-12 dated 2010, 1.5V DC. Yes, got money's worth out of this original part, over twelve years strong. Clicker stopped clicking from previous attempts to clean battery corrosion off. Looked up part at ProComm heater site and the current ignitor part number is PIMSC1-01 but out of stock. Took a chance on this one and it fits. Important to know is the hole to accept the ignitor on the heater has to be approximately 3/4 of an inch across to fit ignitor into hole. If hole is smaller, then may need to file down edge on heater a little to fit. This fit our propane heater fine with no adjustment. If you open the heater and the ignitor looks similar this should work. We bought the one plug model. The ignitor block has a flat square plug end embedded in the bottom corner. The thin wire on the heater is round looking, but it still fits on a blade end. The ignitor plug blade must be aligned with the seam in the wire plug. The existing wire on the unit looks like a round end but fits on a flat square blade. Did not think it would fit, but looked at original part blade and it is the same as new part, flat blade. Blade aligns with seam then slips on. Round wire end to square, works. For heater install. Took the screws off face of heater, unscrewed the old ignitor part, pulled off wire, positioned the new ignitor in heater hole, spun on the included plastic nut, dropped in a AAA battery, put the rubber cap on it and now clicks away like normal. This was a good price and with prime was delivered next day. Now if it lasts as long as the original then great. Just remember to take out the batteries when not in use for the season or occasionally check for leaky batteries. Hope those with a propane heater find this helpful since this is advertised mostly for bbq grills. It just basically clicks to make a spark to ignite the pilot light.

The Onlyfire Spark Generator arrived quickly, well-packaged, and exactly as described. Installation was simple and straightforward. Quick swap out, no special tools or complicated steps required. Within minutes, my fireplace was sparking the flame and igniting like new. This little ignitor proved to be a quick, effective solution to what I thought might turn into a bigger repair project. If you need a reliable push-button igniter replacement that installs easily and works immediately, this is it, for sure!!!

As the Hemptons stated it is not exact fit. Make sure you measure the diameter of mounting hole in your grill before you order. Luckily I have a step drill that I was able to widen the hole. Other than that it works great!

Purchased this to put on my fireplace for sunroom and so glad I did. Was easy to install and works great. Saved me money not having to pay a repairman.

Perfect replacement, identical to the igniter on our gas logs. Prompt delivery and perfect operation.

Worked great. It is larger than the original. Good price!

Great item. So tired of lighting fire pit with a lighter. This fit perfectly and my furepit is a joy again.

It seemed like a solid built ignitor . Worked great for about a week then died 🤔 . I used one to make a custom electric starter on my RV propane cooktop. I was lovng this thing until it just crapped out after a week. I thought it might be a battery or loose connection issue but after several tries , even w a simple test jumper, it just wouldnt come back to life. Im sending it back & may try again w this brand , might be a one-off qc problem.

Este producto no lo encontré en ninguna de las tiendas especializadas de boilers y aparatos similares en monterrey, en Amazon lo encontré y llego muy rápido. Funciona ala perfeccion

This is my second time buying this exact ignitor for different grills — both times it worked like a charm. It was easy to install (just needed a 7/8" hole) and connected quickly to standard burners. The spark is strong, and it lights up the BBQ on the first try every time. No battery included, so make sure to have a fresh AA on hand. For under $10, it’s a cheap fix that works just as well as the original part.

Five stars for selling a product that fits a AAA battery! The starter for the infrared on the BBQ was no longer functional, plus we somehow lost the rubber part, so we purchased this to replace it. After installing we realized that the disconnect connector was detached, so we headed to the car parts section of Canadian Tire to find the right replacement, connected that and soldered a bit, then added a shrink wrap tube to prevent erosion and connected to this part and voila! The infrared works perfectly!

I give it a 4 star because I just installed it so only time will tell if it's worth the value but it's working so far and it wasn't hard to install at all. Will let you know if it last through the summer cookouts .

Perfect fit. Works great.